Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru Screw Clamp
External Toolholders [DC Insert]
SDJC-FF (Without Offset) (External / Copying)
S F1 F2 L2
32° 32°
S F1 H1 B
93° 32° L1
Toolholder Dimensions SDJC$0808F-07FF 0°
Description SDJC$1010JX-11FF
SDJC$1212..-11FF h
shows above figure.
Right-hand shown
Std. Dimension (mm) Standard Corner-R(r) Clamp Screw Spare Parts E
R L H1=h B L1 L2 F1 F2 S Wrench
SDJC 0808F -07FF 88 14 8 0.5 SB-2570TR FT-8
SDJC 1212F -11FF 85 0 0.2 FT-15
1010JX-07FF 12 12 20 12 1 SB-4085TR FT-8 H1 B
1010JX-11FF
1212JX-11FF 10 10 - 10 - 0.2 SB-2570TR FT-15 Small Tools
1616JX-11FF
10 10 120 20 10 3 0
0.2 SB-4085TR
12 12 12 1
16 16 - 16 -
SDJC (External / Copying)
32
32 h F1 L2
93 Standard Corner-R(r)93
0
L1
Applicable Inserts Right-hand shown Clamp Screw Spare Parts
Description Wrench
Std. Dimension (mm)
R L H1=h B L1 L2 F1
SDJC 1010F -07 10 10 80 12 12 0.2 SB-2570TR FT-8
SDJC 1010F -11 0.2 SB-4085TR FT-15
1212H -11 10 10 80 12
1616H -11
2020K -11 12 12 16
2525M -11 16 16 100 18 20
20 20 125 25
25 25 150 32
Applicable Inserts
Applications Minute ap Finishing Finishing-Medium Finishing-Medium Medium Medium Finishing Finishing / Precision Low Feed Finishing / Precision
Ref. Page B52 B52 B53 B53 B54 B53 B55 B56
B55 B56
CF GF GK GQ FN-Z Standard -F F -USF
-FSF (E / F) -U
Insert
Toolholder
SDJC ...-07FF/-07 DCGT0702.. DCGT0702.. DCMT0702.. DCGT0702.. DCGT0702.. DCGT0702.. DCGT0702.. DCET0702.. DCGT0702.. DCET0702..
SDJC ...-11FF/-11 DCGT11T3.. DCGT11T3.. DCMT11T3.. DCGT11T3.. DCGT11T3.. DCGT11T3.. DCGT11T3.. DCET11T3.. DCGT11T3.. DCET11T3..
DCMT11T3..
Applications
Ref. Page Low Feed Low Feed / Precision Low Carbon Steel Finishing Low Carbon Steel Stainless Steel Cast Iron Non-ferrous Metals Non-ferrous Metals Non-ferrous Metals Hard Materials
Finishing-Medium
B57 B57 B54 B54 B54 B57 B57 B57 C19 C11
(E / F) -J F -JSF XP XQ MQ Without Chipbreaker AH -A3 PCD CBN
Insert
Toolholder
SDJC ...-07FF/-07 - - DCMT0702.. - DCMT0702.. DCGW0702.. - - DCMT0702.. DCMW0702..
SDJC ...-111FF/-11 DCGT11T3.. DCET11T3.. DCMT11T3.. DCMT11T3.. DCMT11T3.. DCGW11T3.. DCGT11T3.. DCGT11T3.. DCMT11T3.. DCMW11T3..
: Std. Item For recommended cutting conditions, see page E38
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru E23