Kyocera - Основной каталог 2011-2012 ENG

                                                             для заказа - kyocera@kyocera-tools.ru                                                                        Screw Clamp

STLN (External / Up Facing)

                                                                                                                                                                               Side Rake Angle: -6°
                                                                                                                                                                              Angle of Inclination: -7°

                                                                                                                   4 '                 Standard Corner-R(r)
              5° -
                                                                                                                                                                    ) #
                                                                                                                                       -

                                                                                                                             

                                                                          I

                                           Right-hand shown

Toolholder Dimensions

                                                            Dimension (mm)                                                                           Spare Parts              Applicable                                E
                                  Std.                                                                                                     Clamp Screw Wrench                   Inserts

Description                                 H1=h B L1 L2 F1 S

STLNR       1010K-09FF            10                         10 120                10
            1212F-09FF            12                                  85           12
            1212K-09FF            16                                               16  0                                                   0.2 SB-2570TR LTW-8SS              TNGU0903..                                Small Tools
            1616K-09FF                                       12 15
                                                                     120

                                                             16

Applicable Inserts

              Applications        Finishing                              Low Feed
                Ref. Page           B44
                                                                          B44
                            FR-F                             (E / F) R-U

              Insert

Toolholder

STLNR...-09FF                     TNGU0903..                 TNGU0903..

Smaller double sided tooling for precision machining                                   Double-sided design allows all edges to be used. Compared to the positive type,
                                                                                       the double-sided design offers less cost per insert and more stability.

            TNGU09 Type           TNGG16 Type                                          Surface roughness comparison (Sharp edge)Surface roughness Ra(m)

                                                                                                              2.0

                                                                                                                                       Negative Type

                                                                                                                                           DNGU080302MFR-U (PR1025)
                                                                                                              1.5

                                                                                                                    1.0

                                                                                                                                                      Positive Type

                                                                                                                    0.5
                                                                                                                                                    DCGT11T302MFR-U (PR1025)

                                                                                                                    0.0

Small Negative Insert             Negative Insert                                                                 0 10                     20 30 40                       50

                                                                                                                       Cutting Time (min)

                                                                                       Workpiece Material : C45 Vc=100m/min, ap=1.5mm, f=0.03mm/rev, Wet

                                                                                                                                                                          Internal evaluation

                                                                                       Case Studies

Recommended Cutting Conditions                                                                                      X10CrNiS18-9 (SUS303)

Workpiece     PR1005              Insert Grade               PR1225                     Spool                                              8
 Material                                                                                                                                                                                          6
                                   PR1025                    Vc=100m/min
                                                                (60~150)                Vc=66m/min
Free-cutting  Vc=100m/min                                                               ap=1.25mm                                                                                    48
    steel        (60~150)                                    Vc=100m/min                f=0.025mm/rev                                                                     Required Surface Roughness: 0.8mRa
                                                                (60~150)                Wet
                                                                                       

                                                                                        Vc=130m/min
                                                                                        ap=0.25mm
                                                                                        f=0.025mm/rev
                                                                                        Wet

Carbon Steel  Vc=100m/min         Vc=100m/min                                          DNGU080302MF-SK (PR1025) 60,000 pcs/insert (4 corners)
 Alloy Steel     (60~150)            (60~150)

Stainless                         Vc=100m/min                                          Competitor D (DCGT type)                                                           20,000 pcs/insert (2 corners)
  Steel                              (60~150)

Continuous to Light Interruption / 1st Choice                                          Competitor D (DCGT type) machined 10,000 pcs/edge. PR1025 machined 15,000 pcs/edge result-
Continuous to Light Interruption / 2nd Choice                                          ing in 3 times longer tool life per insert.

                                                                                                                                                                                             Evaluation by the user

: Std. Item : Check Availability

                                  для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru                                                                                                                           E17