Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
Recommended Cutting Conditions
Recommended Cutting Conditions - External Turning (Negative Insert) (ap indicates radius)
ISO Workpiece Cutting Recommended Recommended Corner-R Lower Limit - Recommendation - Upper Limit
Range Chipbreaker Grade (r)
Material Hardness Application
Classication vc(m/min) ap(mm) f(mm/rev)
Finishing Continuous HQ TN6020 0.8 120 - 160 - 200 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
TN6020 0.8 100 - 120 - 150 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
(Gloss Oriented) Interruption
Continuous MQ CA6515 0.4 120 - 180 - 240 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
CA6525 0.8 100 - 160 - 220 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
Finishing
Interruption
D Stainless HB Medium-Roughing Continuous MS CA6515 0.4 120 - 160 - 200 1.0 - 2.0 - 3.0 0.1 - 0.2 - 0.3
220 (Chip Control Oriented) Interruption CA6525 0.8 80 - 140 - 180 1.0 - 2.0 - 3.0 0.2 - 0.3 - 0.4
Steel
Medium-Roughing Continuous MU CA6515 0.4 120 - 160 - 200 1.0 - 2.0 - 3.0 0.15 - 0.25 - 0.35
(Sharpness Oriented) Interruption CA6525 0.8 80 - 140 - 180 1.0 - 2.0 - 3.0 0.15 - 0.25 - 0.3
M Roughing Continuous CA6515 0.8 100 - 140 - 180 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
CA6525 1.2 80 - 120 - 150 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Standard
Interruption
External Finishing Continuous HQ TN6020 0.8 100 - 120 - 150 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
(Gloss Oriented) Interruption TN6020 0.8 80 - 100 - 120 0.5 - 1.0 - 1.5 0.05 - 0.08 - 0.1
Stainless Continuous MQ CA6515 0.4 100 - 120 - 150 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
Steel MS CA6525 0.8 80 - 100 - 120 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.15
Finishing MU CA6515 0.4 100 - 120 - 150 1.0 - 1.5 - 2.0 0.1 - 0.15 - 0.25
CA6525 0.8 80 - 100 - 120 1.0 - 2.0 - 3.0 0.1 - 0.15 - 0.2
Interruption CA6515 0.4 100 - 120 - 150 1.0 - 1.5 - 2.0 0.1 - 0.15 - 0.25
HB Medium-Roughing Continuous CA6525 0.8 80 - 100 - 120 1.0 - 2.0 - 3.0 0.1 - 0.15 - 0.2
300 (Chip Control Oriented) Interruption
Medium-Roughing Continuous
(Sharpness Oriented) Interruption
Roughing Continuous CA6515 0.8 80 - 100 - 120 1.0 - 2.0 - 3.0 0.2 - 0.3 - 0.4
CA6525 1.2 60 - 80 - 100 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Standard
Interruption
High Speed Continuous Without KBN60M 0.8 400 - 700 - 900 0.05 - 0.2 - 0.5 0.03 - 0.05 - 0.1
Cutting Continuous Chipbreaker KBN900 1.2 500 - 900 -1200 0.1 - 0.5 - 1.0 0.05 - 0.1 - 0.2
Interruption KBN900 1.2 500 - 700 - 900 0.5 - 1.0 - 1.5 0.05 - 0.1 - 0.2
Finishing Continuous PV7005 0.8 300 - 350 - 400 0.5 - 1.0 - 1.5 0.1 - 0.2 - 0.3
(Gloss Oriented) TN6020 0.8 100 - 150 - 200 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
Standard
Interruption
Gray Cast HB Finishing Continuous KA30 1.2 300 - 500 - 700 0.3 - 0.5 - 1.0 0.1 - 0.2 - 0.3
Iron 250
(Ceramic) Interruption Without PT600M 0.8 300 - 450 - 600 0.3 - 0.5 - 1.0 0.1 - 0.2 - 0.3
Medium Continuous Chipbreaker CS7050 1.2 300 - 450 - 550 1.0 - 2.0 - 3.0 0.15 - 0.25 - 0.35
(Ceramic) Interruption KS6050 1.2 250 - 400 - 500 1.0 - 2.0 - 3.0 0.15 - 0.2 - 0.3
K Medium Continuous CA4505 0.8 200 - 250 - 300 0.5 - 2.0 - 2.5 0.1 - 0.2 - 0.3
CA4515 1.2 150 - 200 - 250 0.5 - 2.0 - 2.5 0.08 - 0.15 - 0.2
Standard
Interruption
Continuous ZS CA4505 0.8 200 - 250 - 300 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
CA4515 1.2 150 - 200 - 250 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Roughing
Interruption
High Speed Continuous Without KBN60M 0.4 200 - 300 - 400 0.1 - 0.3 - 0.5 0.1 - 0.15 - 0.2
Cutting Interruption Chipbreaker PT600M 0.8 200 - 250 - 35 0.1 - 0.5 - 1.0 0.1 - 0.2 - 0.4
Nodular Cast HB Finishing Continuous Standard PV7005 0.8 150 - 250 - 300 0.5 - 1.0 - 1.5 0.1 - 0.2 - 0.3
(Gloss Oriented) Interruption TN6020 0.8 100 - 150 - 180 0.5 - 1.0 - 1.5 0.08 - 0.15 - 0.2
Iron 270 Medium Continuous CA4505 0.8 150 - 200 - 250 0.5 - 2.0 - 2.5 0.1 - 0.2 - 0.3
CA4515 1.2 120 - 180 - 220 0.5 - 2.0 - 2.5 0.08 - 0.15 - 0.2
Standard
Interruption
Continuous ZS CA4505 0.8 150 - 200 - 250 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
CA4515 1.2 120 - 180 - 220 1.0 - 2.0 - 4.0 0.2 - 0.3 - 0.4
Roughing
Interruption
High Speed Cutting Without KPD001 0.4 300 - 800 -2000 0.05 - 0.5 - 1.0 0.05 - 0.1 - 0.15
(Rainbow Surface Gross)
Continuous
N Non-ferrous HB
Chipbreaker
Metals Continuous A3 KW10 0.8 400 - 500 - 700 0.5 - 1.0 - 2.0 0.1 - 0.2 - 0.25
KW10 0.8 400 - 500 - 700 0.5 - 1.0 - 2.0 0.1 - 0.2 - 0.25
100 Finishing
Interruption
Medium Continuous AH KW10 0.8 200 - 300 - 500 1.0 - 2.0 - 3.5 0.1 - 0.3 - 0.4
Interruption KW10 0.8 200 - 300 - 500 1.0 - 2.0 - 3.5 0.1 - 0.3 - 0.4
Precision Cutting Continuous Without KPD001 0.4 100 - 150 - 180 0.05 - 0.3 - 0.5 0.03 - 0.1 - 0.15
HB (Rainbow Surface Gross) Interruption Chipbreaker KPD001 0.4 70 - 120 - 150 0.05 - 0.3 - 0.5 0.03 - 0.07 - 0.1
0.4 40 - 70 - 100 0.2 - 0.5 - 1.0 0.05 - 0.2 - 0.3
Titanium Alloy Continuous MQ SW05 0.4 40 - 70 - 100 0.2 - 1.5 - 1.0 0.05 - 0.15 - 0.2
SW05 0.8 40 - 60 - 80 0.5 - 1.0 - 3.0 0.1 - 0.25 - 0.35
400 Finishing 0.8 40 - 60 - 80 0.5 - 1.0 - 3.0 0.1 - 0.2 - 0.3
S Interruption
Medium Continuous MU SW05
Interruption SW05
Heat-resistant HB Continuous MQ PR1310 0.4 40 - 60 - 80 0.2 - 0.5 - 1.5 0.03 - 0.08 - 0.12
PR1310 0.8 40 - 60 - 80 0.2 - 0.5 - 1.5 0.05 - 0.1 - 0.15
Finishing
Interruption
Alloys 350 Medium Continuous MS PR1310 0.8 40 - 60 - 80 0.5 - 1.0 - 2.0 0.05 - 0.1 - 0.15
Interruption PR1310 1.2 40 - 60 - 80 0.5 - 1.0 - 2.0 0.1 - 0.15 - 0.2
40 50 Finishing Continuous HQ CA5515 0.8 60 - 100 - 120 0.1 - 0.3 - 0.5 0.05 - 0.08 - 0.1
HRC Interruption Standard CA5515 0.8 30 - 50 - 70 0.1 - 0.3 - 0.5 0.05 - 0.08 - 0.1
H Hard 40~50 HRC Finishing Continuous Without PT600M 0.8 60 - 80 - 100 0.2 - 0.5 - 0.7 0.05 - 0.1 - 0.15
Materials 50~65 HRC Finishing Interruption Chipbreaker PT600M 1.2 30 - 40 - 60 0.2 - 0.5 - 0.7 0.05 - 0.1 - 0.15
Continuous Without Chipbreaker KBN05M 0.8 100 - 150 - 200 0.05 - 0.3 - 0.5 0.05 - 0.08 - 0.1
50~68 Interruption SET,MET KBN25M 1.2 80 - 120 - 160 0.05 - 0.3 - 0.5 0.05 - 0.08 - 0.1
HRC Medium Continuous Without KBN900 1.2 80 - 100 - 120 0.5 - 1.0 - 2.0 0.05 - 0.1 - 0.2
Interruption Chipbreaker KBN900 Radius Plus 70 - 90 - 110 0.3 - 0.7 - 1.0 0.05 - 0.1 - 0.15
D40 для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru