Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru Lever Lock
PDJN (External / Copying)
32 Side Rake Angle: -6°
Angle of Inclination: -7°
F1 H1 B
h F2 Applicable Inserts
Toolholder Description
93 L2 L1 DN A
DN G
PDJN ...-11 1104..
3 PDJN ...-15 DN A 1504..
Right-hand shown PDJN ...-15U
DN G 1506.. D
DN M (1504..)
PDHN (External / Face Grooving / Copying)
17.5 Side Rake Angle: -6° External
Angle of Inclination: -6°
Applicable Inserts
17.5
F1 Standard Corner-R(r)
h F2 17.5 Toolholder Description
L2 L1 H1 B
17.5 DN A 1504..
(1506..)
PDHN ...15 DN G
DN M
Right-hand shown
Std. Dimension (mm) Lever Lock Screw Spare Parts Wrench
Shim Shim Pin Punch
Description FH
R L H1=h B L1 L2 F1 F2
LW
PDJN 1616H -11 16 16 100 20 -
2020K -11
2525M -11 20 20 125 28 25 - 0.4 LL-1DN LS-1N LD-32N LSP-1 PC-1 FH-2.5
25 25 150 32 27
2020H -15* 20 20 100 25 -
2020K -15
2525M -15 20 20 125 36 25 - 0.8 LL-3N LS-2N LD-42 LSP-2 PC-2 LW-3
3225P -15 25 25 150 32 25 *LD-42-20
32 25 170 32 25
2525M -15U 25 25 150 32 25 LD-42
3232P -15U 36 0.8 LL-4 LS-3 *LD-42-20 LSP-2 PC-2 LW-3
32 32 170 40 28
(LD-43)
(*LD-43-20)
PDHN 2020K -15 20 20 125 25 22 LD-43
2525M -15 36 0.8 LL-4 LS-3 *LD-43-20 LSP-2 PC-2 LW-3
25 25 150 32 24
(LD-42)
(*LD-42-20)
* mark indicates short shank type.
Shim: PDJN -15U ...LD-42 is attached to PDJNR / L-15U. When using DN 1504 type insert, prepare LD-43 separately.
PDHN ...LD-43 is attached to PDHN. When using DN 1506 type Insert, prepare LD-42 separately.
When using inserts with a corner R(r) that is greater than 1.6mm, please purchase a shim with * mark and use it in order to prevent workpiece and shim from interfering with each other.
Applicable Inserts
Application Finishing Finishing- Finishing- Finishing- Finishing- Medium- Medium- Medium-Roughing Roughing Roughing Roughing
GP Medium Medium Medium Medium Roughing Roughing PT GT Standard PH
HQ CQ CJ TK GS PS
Insert
Size 1104,1504,1506 1104,1504,1506 1504,1506 1504,1506 1506 1104,1504,1506 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506
B20 B21 B21
Page B20 B20 B20 B20 B21 B21 B21 B21
Medium Soft Steel Stainless Steel
Application One side / Roughing• Finishing Finishing Soft Steel / Soft Steel / Stainless Finishing Stainless Medium to Stainless Medium to
High Feed Rate XP -T Medium cutting Roughing GU
Roughing Roughing
PX -S XQ XS MQ MS MU
Insert
Size 1504,1506 1104 1104,1504 1504 1504 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506
Page B22 B22 B22 B22 B22 B22 B22
B21 B23 B23 Cast Iron Cast Iron
Application Cast Iron ZS GC
Stainless Steel Stainless Medium Cast Iron Non-ferrous Metals Non-ferrous Metals Non-ferrous Metals Hard Materials
to Roughing
-ST TK C Ceramic AH -A3 PCD CBN
Insert
Size 1506 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506 1504 1504 1504,1506
Page B22 B22 B23 B23 B23 B86 B23 B23 C17 C6
For recommended cutting conditions, see page D39~D40
: Std. Item : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru D11