Kyocera - Основной каталог 2011-2012 ENG
для заказа - kyocera@kyocera-tools.ru
[Cermet / Coated Carbide / Carbide]
80°Trigon / Positive with Hole (mm)
Description A T d
WP_1102_ 6.35 2.38 2.8 11
WP_1603_ 9.525 3.18 4.4 11
80° P Free-Cutting Steel Classification of usage B
Carbon steel / Alloy steel : Interruption / 1st Choice
r M Stainless Steel : Interruption / 2nd Choice Positive
Gray Cast Iron : Light Interruption / 1st Choice Insert
Insert K Nodular Cast Iron : Light Interruption / 2nd Choice
Non-ferrous Metals : Continuous / 1st Choice C
Handed insert A d N Heat-Resistant Alloys : Continuous / 2nd Choice D
shows L-Hand Titanium Alloy R
T S Hard materials (In case hardness is under 45HRC) S
Description T
H V
WPMT 110204GP W
Dim. Cermet MEGACOAT CVD Coated PVD Coated MEGACOAT Carbide Ref. Page for Toolholder
(mm) Cermet Carbide Carbide
Applicable
r TN6010 Chipbreaker Range
TN6020
(ap indicates radius)
TN60
PV7005
PV7010
PV7025
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
PR1225
PR1305
PR1310
PR1325
KW10
SW05
Finishing 0.4 (mm)
3 (Steel / Edge Length=11)
WPMT 160304GP 0.4 ap 2 HQ
1 GP
Y
Finishing-Medium PMT 110202HQ 0.2 Insert (Turning)
110204HQ 0.4
WPMT 160304HQ 0.4 0.1 0.2 0.3 0.4
160308HQ 0.8 f (mm/rev)
WPGT 110202 -Y 0.2 (mm)
110204 -Y 0.4 (Steel / Edge Length=16)
4
Finishing-Medium WPGT 160304 -Y 0.4 L F57 3 Y
160308 -Y 0.8 L F59 ap
2
WPGT 110202M -Y < 0.2 1 HQ
110204M -Y < 0.4 GP
WPGT 160304M -Y < 0.4 0.1 0.2 0.3 0.4
160308M -Y < 0.8 f (mm/rev)
Cast Iron WPGW 110202 0.2
110204 0.4
Without Chipbreaker WPGW 160304 0.4
160308 0.8
Insert whose corner R(r) dimension expressed with less than sign (e.g.<0.05, <0.1, <0.2 etc.) indicate models with minus tolerance for corner R (r).
80°Trigon / Positive with Hole
80° (mm)
Description A T d
WP__1102_ 6.35 2.38 2.8
11°
WP__1603_ 9.525 3.18 4.4
r A T
dDescription
Insert TN30 Cermet
PV30
Handed insert PV60
shows L-Hand PV90
PV7020
CA4010
CA4115
CA4120
PR915
PR905
Ref. Page for
Toolholder
TN30 Cermet
PV30
PV60
PV90
PV7020
CA4010
CA4115
CA4120
PR915
PR905
Ref. Page for
Toolholder
Dim. PVD CVD PVD Insert Description Dim. PVD CVD PVD
(mm) Coated Coated Coated (mm) Coated Coated Coated
Cermet Carbide Carbide Handed insert Cermet Carbide Carbide
r shows L-Hand r
L F57
WPMT 110204GP 0.4 Finishing-Medium WPGT 110202 -Y 0.2 L L F59
110204 -Y 0.4
Finishing WPMT 160304GP 0.4 F57 L
F59 WPGT 160304 -Y 0.4
WPMT 110202HQ 0.2 160308 -Y 0.8
110204HQ 0.4
Finishing-Medium WPMT 160304HQ 0.4
160308HQ 0.8
Inserts are sold in 10 piece boxes. B79
: Std. Item R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) : Check Availability
для заказа - kyocera@kyocera-tools.ru www.kyocera-tools.ru