Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Molded Chipbreaker Cross Reference Table This table is Kyoceras own estimation based on publications and is
not authorized by companies mentioned in it.
Negative Inserts
Kyocera
Cutting Range General Chipbreaker for Hitachi Iscar Kennametal Mitsubishi NTK Sandvik Seco Sumitomo Tungaloy
Chip- Sticky Material / WIDIA
breaker Soft Steel
Finishing WP FW SW WF MF2 LUW AFW
(With Wiper Edge)
Finishing - Medium WQ WG MW MW WM M3 GUW ASW
(With Wiper Edge)
Finishing DP XP BE BH SF FF F FH WM QF SU FP TF 01
GP UF FS FY ZF1 PF FF1 SP FA AS
Carbon Steel / Alloy Steel VF XP-T FE
PK FL LU TSF
Finishing - HQ AB B SH C WV EX GU TS NS
SA MV WR SK SJ NM CB
Medium CQ XQ CE NF FN QM MF2 SX UU 11 17
SY 27 ZF
CJ CT UJ
Medium - GS XS AE TF MN MA Z5 SM M3 UA DM
Roughing CS DE MH ZW1 PM MF3 UG TM
HS AH ZM
PS
AR
Medium-Roughing PT AY NR P GH GS MR M5 MU TH 32Y
High Feed Rate GT MR5 UX 32 37
HT RE
Roughing Standard H HX GN PR MG MT G Standard MR7 MC MU 31 33
PH HE TE RN Standard 23 MX UZ F-K
Roughing UE NM RH HV HX QR PR R4 R5 HG HP TU
PX BH RM HZ HXD HR R6 R7 MP 57 65
MP
One Side / High Feed Rate RP
Non Finishing GU FP FS SH ZF1 MF SU SS
MQ FJ
ferrous Cast Iron Stainless Steel
Medium - MS DE MS MA
Metals Roughing MU SE
TK PV TF MP MJ ZP WS MM MF1 MF3 EX MU SM SA
PP ES MH
MR A3 A5 UP S
GH GJ
Medium C AH VA Standard KF GZ UX Standard
Roughing Standard VY UN GH KM UJ 33 CF
GC KR UZ CM
ZS CH
Medium - Roughing AH PP GP AL 95 AG P
MS
Positive Inserts Kyocera Iscar Kennametal Mitsubishi NTK Sandvik Seco Sumitomo Tungaloy
Cutting Range WIDIA
General Chipbreaker for Hitachi AZ3 PF
Chip- Sticky Material / AZ7 UF
breaker Soft Steel AF1 PM
QD UM
Steel Minute ap CF AM3 PF 01
PM
Alloy Finishing DP GP XP PF 11 GF FV SQ PR UR FF1 FC FK PF
VF SM UF SV SMG KM FP LU 23
PS
/ MF SF 24
SU
Steel Finishing - Medium HQ XQ JE 14 LF MQ MV AL F1
Carbon Finishing - Medium GK JQ No R
Indication
Medium Standard J Standard GM Standard F2 MU PM
MR SC
Stainless Finishing MQ WF FW FV LU PF
Steel MW SS
Non Finishing - Medium AH AF HP AZ AG AL Technical
ferrous AS AW Information
Metals
Positive Inserts (Automatic Lathe)
Cutting Range Kyocera Hitachi Iscar Kennametal Mitsubishi NTK Sandvik Seco Sumitomo Tungaloy
WIDIA
Carbon Steel / Alloy Steel Minute ap CF JQ PF 11 FV AZ7 PF FF1 FC 01
Finishing CK MP SM UF SV SMG ZR PF
Finishing - Medium GF PS
Medium GQ JE 14 LF AM AM3 PM F1 SU PM
MV
GK
J Standard MF Standard QD PR F2 SC
Stainless Finishing MQ WF FW FV MF LU PF
Steel Finishing - Medium AH MW
Non AF HP AZ AL AG AL
ferrous AS AW
Metals
kyocera@kyocera-tools.ru R21
www.kyocera-tools.ru