Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Combination of Applicable Inserts
Clamp Screw Edge Width A Line B Line C Line Wrench Tightening
(Standard
Description attachment mm inch Applicable Clamp Applicable Clamp Applicable Clamp For Torque
parts) (mm) Insert Screw Insert Screw Insert Screw Clamp (Nm)
Screw
MSTB AN0607- T 6 LNEU1235.. SE-40050TR LNEU1235.. SE-40050TR
SN0607- T 6.5 -
SE-40050TR 7 - -
LNEU1240.. SE-40055TR LNEU1240.. SE-40055TR
MSTB AN0809- T 8 LNEU1245.. SE-40068TR LNEU1245.. SE-40068TR
SN0809- T 8.5 -
SE-40068TR 9 - -
LNEU1250.. SE-40080TR LNEU1250.. SE-40080TR
Metric
MSTB AN1011- T 10 LNEU1245.. SE-40068TR
SN1011- T 10.5 LNEU1245.. SE-40068TR LNEU1245.. SE-40068TR
SE-40068TR 11 -
LNEU1250.. SE-40080TR
LNEU1250.. SE-40080TR LNEU1250.. SE-40080TR
MSTB AN1213- T SE-40090TR 12 LNEU1255... SE-40090TR
12.5 LNEU1255... SE-40090TR LNEU1255... SE-40090TR
13 -
LNEU1260... SE-40100TR
LNEU1260... SE-40100TR LNEU1260... SE-40100TR
.250 LNEU1240.. SE-40055TR
(6.35mm)
LNEU1240.. SE-40055TR - TT-15L
.270 LNEU1245.. SE-40068TR 3
MSTB AN250- T SE-40055TR - -
(6.86mm)
.289 LNEU1245.. SE-40068TR
(7.34mm)
.312 LNEU1245.. SE-40068TR
(7.92mm)
LNEU1245.. SE-40068TR -
.332 LNEU1250.. SE-40080TR
Inch spec MSTB AN312- T SE-40068TR - -
(8.43mm)
.351 LNEU1250.. SE-40080TR
(8.91mm)
.375 LNEU1245.. SE-40068TR
(9.525mm) LNEU1245.. SE-40068TR LNEU1245.. SE-40068TR
MSTB AN375- T SE-40068TR - .395
(10.33mm) LNEU1250.. SE-40080TR
.414 LNEU1250.. SE-40080TR LNEU1250.. SE-40080TR
(10.52mm)
.500 LNEU1255... SE-40090TR
(12.7mm) LNEU1255... SE-40090TR LNEU1255... SE-40090TR
MSTB AN500- T SE-40090TR - .520
(13.21mm) LNEU1260... SE-40100TR
.539 LNEU1260... SE-40100TR LNEU1260... SE-40100TR
(13.69mm)
* For clamp screw, above listed “Standard attachment parts” are attached. In case of necessity of another size of clamp screw by changing slotting width, please purchase separately.
Slot width (edge width) adjustment M
1 2 3 4 10 B Line
C Line
6 6.5 7
A Line C Line A Line C Line A Line C Line A Line
Milling
The Slot width (edge width) of MSTB-Type slot Mills is adjustable by a maximum of 1mm (.039'') with the combination of inserts.
1. In the case of MSTB AN0607- T the width (W) is 6mm by installing LNEU1235 on both A line and C line.
2. By replacing C line only with LNEU1240 the width (W) is 6.5mm.
3. By replacing A line and C line with LNEU1240 the width (W) is 7mm.
4. If the slotting width (edge width) is 10mm (.375''), the B line (middle edge) is necessary.
* Caution
1) There is no description such as “A line”, “B line”, and “C line” on the actual slot Mill. These are only for explanation of the combination of insert.
2) Use proper clamp screws for applicable inserts on the basis of the above chart.
3) Please do not use, that has a difference of width more than 1mm (.039'').
Bottom cutting shape of MSTB Slot Mill 176
Slot bottom shape will be (Fig.1) convex shape.
Fig.1 Convex bottom shape
kyocera@kyocera-tools.ru M103
www.kyocera-tools.ru