Kyocera - Основной каталог 2010-2011 ENG

                                             для заказа - kyocera@kyocera-tools.ru

Set up

              Wrench support hole                                                                                             How to attach inserts

                                             IN indicated side                                                                                  1. Put insert inside the slot mill.
                                                                                                                                                2. Insert one of the pin on the wrench (on IN indicated
                                        Hardness
                                            (HB)                                                                                                    side) into the wrench support hole.
                                                                                                                                                3. Using the other pin, push the front relief surface of
                                                                                                             OUT IN
                                                                                                                                                    the insert.
                                                                                                                                                4. Rotate the wrench until insert's back end makes

                                                                                                                                                    contact with slot mill.

                                                                              OUT indicated side                              How to detach inserts
           Insert removal hole for wrench
                                                                                                                                                1. Insert one of the pin on the wrench (on OUT indicated
                                                                                                                                                    side) into the wrench support hole, and insert other
                                                                                                                                                    pin into the hole on releasing wrench.

                                                                                                                                                2. Insert can be uninstalled by rotating the wrench
                                                                                                                                                    counter clock wise. (A magnet is installed out side)

Note) Use appropriate wrench for set up.

   Recommended Cutting Conditions

                                             Recommended Insert Grade (Cutting Speed Vc: m/min)                                                  fz (mm/t)             Remarks

Workpiece Material                           CVD Coated Carbide PVD Coated Carbide                                                               Edge Width (mm)
                                                                                                                                                  2.2 3.0
                                             CA0835                                                                  PR0735   1.6                                 4.0

Low Carbon           St42-2             125  250-310                                                                 200-250  0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20                                      M
     Steel        C10E~C25              190  160-190                                                                 130-160
                                        250  140-180                                                                 110-150  0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20                                      Milling
Carbon Steel       C30~C60              180  140-180                                                                 110-150
                  (Annealed)            275  120-160                                                                 100-130  0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20
 Alloy Steel                            280  100-140                                                                 80-120
                   C30~C60                                                                                                    0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20
High Carbon      (Heat treated)                                                                                                                                                              Coolant
   Carbide
                    34CrMo4                                                                                                   0.03-0.10 0.04-0.12 0.06-0.16 0.08-0.18
                  (Annealed)
                                                                                                                              0.03-0.10 0.04-0.12 0.06-0.16 0.08-0.18
                    34CrMo4
                 (Heat treated)

              X40CrMoV51, etc.

Stainless     X5CrNi1810, etc.          220  150-190                                                                 80-120   0.03-0.10 0.04-0.12 0.06-0.16 0.08-0.18
  Steel         X10Cr13, etc.           300  140-180                                                                 60-80    0.03-0.10 0.04-0.12 0.06-0.16 0.08-0.18

 Gray Cast      GG25~GG35               260  160-200                                                                 - 0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20
     Iron                                                                                                                                                                                             Dry
              GGG40~GGG50               160  130-160
Nodular Cast  GGG60~GGG80               250  110-140                                                                 - 0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20
     Iron                                                                                                            - 0.03-0.12 0.04-0.14 0.06-0.18 0.08-0.20

Note) 1. Use down-cut machining.                                                                  ap
        2. If ap is under 1/10 of Cutter Dia.(D), it is possible                                                                            D
           to increase feed per tooth(fz) 40%.

                                             kyocera@kyocera-tools.ru                                                                                                                                      M99
                                                www.kyocera-tools.ru