Kyocera - Основной каталог 2010-2011 ENG
Endmill [ND для заказа - kyocera@kyocera-tools.ru
Insert]
Recommended Cutting Conditions (MEA)
fz Recommended Insert Grade (Vc: m/min) Max. ap (mm)
Workpiece (mm/t) Cermet PVD Coated Carbide
Material D D TN60
TN100M
12~20 21~80
TC60
PR630
PR730
PR830
PR660
PR905
PW30
KW10
Cutting Dia.
(D)
Slotting
(ap)
Shouldering
(apae)
Stainless Steel 0.03~ 0.07~ 120~200 120~200 120~200 100~200 ~14 1 81
0.08 0.15 120~200 120~200 120~200 100~180 16~28 3 83
100~180 100~180 100~180 80~150 30~80 2 85
Carbon Steel 0.03~ 0.07~ 100~180 80~150 80~150 60~130 1.5 82
0.12 0.15 ~14 6 86
100~200 16~28 3 810
Alloy Steel 0.03~ 0.07~ 30~80 1.5 82
0.12 0.15 5 85
~14 3 810
Metal Mold Steel 0.03~ 0.07~ 16~28 1.5 82
0.1 0.15 30~80 4 84
3 810
Cast Iron 0.05~ 0.1~ ~14 1.5 82
0.15 0.2 16~28 6 86
30~80 4 810
Non-ferrous Material 0.05~ 0.1~ 3 83
0.2 0.25 ~14 6 810
80~150 16~28 4 820
30~80
~14
100~300 16~28
30~80
Reduce the ap by 20-50% when machining with long overhang length or using long shank types. : 1st Recommendation : 2nd Recommendation
Recommended Cutting Conditions (MEB)
Recommended Insert Grade (Vc: m/min) Max. ap (mm)
Workpiece fz Cermet PVD Coated Carbide
Material (mm/t) TN60
TN100M
TC60
PR630
PR730
PR830
PR660
PR905
PW30
KW10
Cutting Dia.
(D)
Slotting
(ap)
Shouldering
(apae)
Stainless Steel ~0.2 120~200 120~200 120~200 100~200 25 2 143
120~200 120~200 120~200 100~180 32, 40 3 145
Carbon Steel ~0.25 100~180 100~180 100~180 80~150 50~80 – 1410
100~180 80~150 80~150 60~130 5 147
Alloy Steel ~0.25 25 5 1410
100~200 32, 40 – 1420
Metal Mold Steel ~0.2 50~80 4 146
5 148
M Cast Iron ~0.25 25 – 1415
32, 40 4 146
Non-ferrous Material ~0.2 50~80 5 148
– 1415
25 6 148
32, 40 5 1412
50~80 – 1420
7 1410
25 5 1415
80~150 32, 40 – 1430
50~80
25
100~300 32, 40
50~80
Slotting with a tool over 50 mm is not recommended. : 1st Recommendation : 2nd Recommendation
Caution of installing Notched Insert
Milling
No. of
Insert
No. of
Insert
No. of
Insert
• Notched Inserts are necessary to be installed correct position. When it is installed wrongly, the tool cannot machine the workpiece and it may
damage the toolholder body.
• Please be minded following tables when you install Inserts to toolholders. Indication is not marked near the Insert pocket for MEA / MEB.
Please refer Table1 or Table2 and make correct combination.
It is not available to install same Notched Insert (-N1, -N2 or -N3).
Table 1 Table 2
NDK 09 type NDK 09 type NDK 15 type
Without With notch Without With notch
Description notch N1 N2 Description Without With notch Description notch N3
11--
MEA 12-S10 notch N1 N2 MEB 25-S20 (-...)
12-S16 2 - 11 25-S25 (-...)
13-S12 MEA 30-S25 4 - 22 32-S25 (-...) 21 1
14-S12 3 - 21 32-S25 (-...) 32-S32 (-...)
16-S12 (-...) 40-S32 (-...)
17-S16 32-S32-W-5T 5 - 32 50-S32 32 1
18-S16 40-S32 63-S32
19-S16 80-S32
20-S16 (-...) 40-S32-110W-6T 6 - 33 42 2
21-S20 50-S32
22-S20 53 2
24-S20 63-S32 8 - 44 63 3
25-S20 (-...) 80-S32
28-S25
MEA 10-S10 (-...) 11--
12-S12-W
16-S16 (-...) 2 - 11
20-S20-Z2
20-S20 (-...) 3 - 21
25-S25
25-S25-W-4T 4 - 22
32-S32
MEA 20-S20-130(W) 2 - 1 1
25-S25-140(W) 3 - 2 1
32-S25-160(W) 4 - 22
40-S32-200(W)
M84 kyocera@kyocera-tools.ru
www.kyocera-tools.ru