Kyocera - Основной каталог 2010-2011 ENG
T5u5r°nDiina mgoInndd/eNxe gaabtliev eI/nwsiдtлeяhrзаtкHаsзoа -lkeyocera@kyocera-tools.ru (mm)
60°Triangle • Negative with Hole Description A T (mm) Description A T d
TN_1103_ 6.35 3.18 TN_1603_ 9.525 3.18 3.81
TN_1104_ 6.35 4.76 d TN_1604_ 9.525 4.76 3.81
2.26 TN_2204_ 12.70 4.76 5.16
2.26
B 60 P Free-cutting steel Classification of usage
Carbon Steel and Alloy Steel : Interruption / 1st Choice
Negative r M Stainless Steel
$ :Interruption / 2nd Choice
% Insert Gray Cast Iron
3 K :Light Interruption / 1st Choice
4 Handed Insert Nodular Cast Iron
5 shows Right-hand : Light Interruption / 2nd Choice
7 A N
8 d Non-ferrous Metals :Continuous / 1st Choice
S Heat-resistant alloy :Continuous / 2nd Choice
TN6010
TN6020T Titanium Alloy (In case hardness is under 45HRC)
TN60DescriptionH Hard Materials
PV7005
PV7010TNGG 110402 -SDim.CermetPVDPVD
PV7020110404 -S(mm)CermetCoated Carbide
CA5505110408 -S
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
r Applicable
Chipbreaker Range
Finishing 0.2 D14
0.4
0.8 F68
Insert (Turning) TNGG 160401 -S 0.1 D14 ap (mm) (Steel / Edge Length=11)
160402 -S 0.2 D15 5
Surface Roughness Oriented 160404 -S 0.4 F43
Super Fine 160408 -S 0.8 F68 4
Finishing TNEG 160402 -SSF 0.2 3
160404 -SSF 0.4
2
B
1S
Sharp Edge / Precision 0.1 0.2 0.3 0.4 0.5
f (mm/rev)
TNGG 110302 -B 0.2 D14
110304 -B 0.4
110308 -B 0.8
TNGG 160304 -B 0.4 — (mm) (Steel / Edge Length=16)
5
0.2 D14
TNGG 160402 -B 0.4 D15 ap ap 4
160404 -B 0.8 F43 C
160408 -B F68
0.2 3 B(Y)
0.4
TNGG 160402 -C 0.8 2
160404 -C 1.2 S
Finishing-Medium-Roughing 160408 -C 1.6
160412 -C 1
160416 -C
25R
0.1 0.2 0.3 0.4 0.5
f (mm/rev)
TNGG 220404 -C 0.4 D14
220408 -C 0.8
D14 (mm)
TNGG 220412 -D 1.2 D68 (Steel / Edge Length=22)
TNGG 110402 0.2 10
110404 0.4 8
110408 0.8 6
TNMG 160404 -C 0.4 4 D
160408 -C 0.8 C
160412 -C 1.2
2
-B: Finishing-Medium D14 0.2 0.4 0.6 0.8 1.0
-C: Medium-Roughing D15 f (mm/rev)
-D: Roughing F43
F68
Medium-Roughing TNGG 160404 -25R 0.4
160408 -25R 0.8
Low Cutting Resistance
For grades TN30 PV60 PR905 , See Page B42~B43
PV30 PV90 PR915
B32 : Std. Item Inserts are sold in 10 piece boxes.
: Check Availability R : Std. Item (R-hand Onlky)yocLe:rSat@d. kItyeomc(eLr-ah-atnodolOs.nrluy)
www.kyocera-tools.ru