Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Milling Indexable Inserts
Milling Inserts Classification of usage P Carbon Steel / Alloy Steel
Mold Steel
TN60
: Roughing / 1st Choice M Stainless Steel TN100M
: Roughing / 2nd Choice
K Gray Cast Iron TC60
Nodular Cast Iron PR630
PR730
: Finishing / 1st Choice N Non-ferrous Metals PR830
PR1025
: Finishing / 2nd Choice S Heat-resistant alloy PR660
(In case hardness is under 45HRC) Titanium Alloy PR905
PW30
H Hard Materials KW10
Dimension (mm) Angle () Ref. Page for Toolholder
Cermet PVD Coated Carbide Carbide
Insert Description A T X Z r
Handed Insert shows Right-hand
X T SDCN 1203AUTN 12.70 3.18 0.5 1.2 - 15° 23° 45°
Z SDKN 1203AUTN 12.70 3.18 0.5 1.2 - 15° 23° 45°
A 15.875 4.76 0.5 1.2 - 15° 23° 45° M31
1203AUFN -
SDKN 1504AUTN
X T
Z
SDKR 1203AUEN-S 12.70 3.18 0.5 1.7 - 15° 23° 45°
A SDMR 1203AUER-H 12.70 3.18 R1.0 0.8 - 15° 23° 45°
T M31
X
Z
A
X T SEEN 1203AFTN 12.70 3.18 0.5 1.4 - 20° 25° 45°
Z
SEKN 1203AFTN 12.70 3.18 0.5 1.4 - 20° 25° 45° M27
A 1203AFFN M28
SEKN 1204AFTN 12.70 4.76 0.5 1.4 - 20° 25° 45° -
M28
M39
Z M27
M28
X r 100 A SEEN 1203AFTR-W 12.70 3.18 - 3.5 B= 20° 25° 45°
A 1203AFFR-W 14.56 -
M32
1-Edge / With Wiper Edge B T
MZ T
SEKN 1203EFTR 12.70 3.18 1.2 1.4 - 20° 25° 15°
Milling X T
Z
SEKR 1203AFEN-S 12.70 3.18 0.5 1.7 - 20° 25° 45°
A
TZ
A
X SEMR 1203AFER-H 12.70 3.18 R1.0 1.0 - 20° 25° 45°
SEMR 1204AFER-H 12.70 4.76 R1.0 1.0 - 20° 25° 45°
4
SOKR 13T3AXEN-J 13.494 3.97 0.5 1.1 - 27° 32° 45°
8
:
!
Cutting Range Chipbreaker Features
S S Chipbreaker for general use cutter. Low resistant cutting is possible with 13° chipbreaker
Finishing- rake angle. Recommended for various ap with 3-step chipbreaker design. Ground wiper
Roughing H edge promotes good surface finish.
Medium- H Chipbreaker for general use cutter. Smooth chip evacuation due to the chipbreaker's
Roughing smooth rake face. 20% less cutting force than no-chipbreaker type due to 25° rake angled
chipbreaker.
Finishing- J Chipbreaker specific to MSO Cutter. Cutting force’s great reduction with 15° chipbreaker’s
Roughing rake angle and 27° positive angle. Back force remains low even increasing the feed rate.
Larger & stronger type insert with thickness 3.97mm and IC 13.494mm, and suitable for
hard-to-machine materials like stainless steel.
SEEN-W type Inserts are sold Inserts are sold : Std. Item : Check Availability
R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
M10 in 5 piece boxes. in 10 piece boxes. kyocera@kyocera-tools.ru
www.kyocera-tools.ru