Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-to[oClse.rurmet / Coated Carbide / Carbide]
(mm)
(mm) Description A T d
60°Triangle • Negative with Hole Description A T d TN_1603_ 9.525 3.18 3.81
TN_1103_ 6.35 3.18 2.26 TN_1604_ 9.525 4.76 3.81
TN_1104_ 6.35 4.76 2.26 TN_2204_ 12.70 4.76 5.16
60 P Free-cutting steel Classification of usage B
r Carbon Steel and Alloy Steel : Interruption / 1st Choice
M Stainless Steel Negative
Insert : Interruption / 2nd Choice $
Gray Cast Iron %
K : Light Interruption / 1st Choice 3
Nodular Cast Iron 4
d : Light Interruption / 2nd Choice
A
N Non-ferrous Metals :Continuous / 1st Choice
T S Heat-resistant alloy : Continuous / 2nd Choice
Description Titanium Alloy
(In case hardness is under 45HRC)
H
Hard Materials
PVD
CVD Coated Carbide Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
r TN60 Applicable
PV7005 Chipbreaker Range
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA411
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
Medium-Roughing TNMG 160404HS 0.4 D14 (mm) 5
160408HS 0.8 D15 (Steel / Edge Length=16) 7
160412HS 1.2 F43 8
F68 5
TNMG 220404HS 0.4 D14 Standard
220408HS 0.8
220412HS 1.2 D14 4 GT
D15 PS(HS)
F43
F68 ap 3
2 PT Insert (Turning)
GS
1
Medium-Roughing / High Feed Medium-Roughing / High Feed Medium-Roughing / High Feed 0.1 0.2 0.3 0.4 0.5
f (mm/rev)
TNMG 160408PT 0.8 (mm)
160412PT 1.2 (Steel / Edge Length=22)
TNMG 160408GT 0.8 ap 10
160412GT 1.2
8 Standard
TNMG 160408HT 0.8 6 PS(HS)
160412HT 1.2
4
2
CQ
0.2 0.4 0.6 0.8 1.0
f (mm/rev)
TNMG 160404 0.4 (mm)
160408 0.8 (Steel / Edge Length=16,22)
160412 1.2
160416 1.6 10
160420 2.0
8 PH (16) PH (22)
0.4
Roughing 0.8 ap 6
1.2
1.6 4
TNMG 220404 0.8 2
220408 1.2
220412 D14 0.2 0.4 0.6 0.8 1.0
220416 0.8 f (mm/rev)
1.2 D14
Medium-Roughing TNMG 160408PH 1.6 D15 (mm)
160412PH F43 (Steel / Edge Length=16,22)
0.8 F68
TNMG 220408PH 1.2 ap ap 10
220412PH D14 8
220416PH 0.8 6 PX (22)
1.2 D14 4
Single Sided / Roughing TNMM 160408PX 1.6 D15 2 PX (16)
160412PX F43
F68 0.2 0.4 0.6 0.8 1.0
TNMM 220408PX f (mm/rev)
220412PX D14
220416PX
High Feed
(mm) (Low Carbon Steel)
5 (Sticky Material)
TNMG 160404XP 0.4 4
160408XP 0.8
Low Carbon Steel D14
D15 3
F43
Finishing F68 2
XP
TNMG 160404XP-T 0.4 XS
160408XP-T 0.8 1 XP-T XQ
0.1 0.2 0.3 0.4 0.5
f (mm/rev)
Finishing / Tough Edge
For grades TN30 PV60 PR905 , See Page B42~B43
PV30 PV90 PR915
B29Inserts are sold in 10 piece boxes.
: Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru