Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
2FESS
General use / Finishing (Short) Recommended Material Number of Flutes: 2
1st Recommendation
Aluminum Non-ferrous Metal Difficult-to-Cut Material Hardened material General Use Sharp I
Std.
Shank Dia.
MEGACOAT is applied %D %TI
%
2
Super Micro-grain carbide
-
Lineup (Unit: mm) (Unit: mm)
Description Outside Outside Length Neck Shank Overall Number Description Std. Outside Outside Length Neck Shank Overall Number
Dia. Dia. of edge Dia. Dia. length of Flutes Dia. Dia. of edge Dia. Dia. length of Flutes
toler- D1 Ds L Z toler- D1 Ds L Z
Dc ance Dc ance
2FESS010-015-04 1.0 0 1.5 1.1 4 45 2 2FESS055-082-06 5.5 0 8.2 5.7 6 50 2
-0.015 -0.015
2FESS015-023-04 1.5 0 2.3 1.6 4 45 2 2FESS060-090-06 6.0 0 9.0 - 6 50 2
-0.015 -0.020
2FESS020-030-04 2.0 0 3.0 2.1 4 45 2 2FESS080-120-08 8.0 -0.005 12.0 - 8 60 2
-0.015 -0.025
2FESS025-037-04 2.5 0 3.7 2.6 4 45 2 2FESS100-150-10 10.0 -0.005 15.0 - 10 70 2
-0.015 -0.025
2FESS030-045-06 3.0 0 4.5 3.2 6 50 2 2FESS120-180-12 12.0 -0.010 18.0 - 12 75 2
-0.015 -0.030
2FESS035-052-06 3.5 0 5.2 3.7 6 50 2 2FESS140-210-16 14.0 -0.010 21.0 14.2 16 75 2
-0.015 -0.030
2FESS040-060-06 4.0 0 6.0 4.2 6 50 2 2FESS150-230-16 15.0 -0.010 23.0 15.2 16 90 2
-0.015 -0.030
2FESS045-067-06 4.5 0 6.7 4.7 6 50 2 2FESS160-240-16 16.0 -0.010 24.0 - 16 90 2
-0.015 -0.030
L 2FESS050-075-06 5.0 0 7.5 5.2 6 50 2
-0.015
This product has attained excellent wear resistance by utilizing the new PVD Coated Carbide technology, “MEGACOAT”. It has also
achieved fracture resistance and stability of machining with its super micro grain carbide. Smooth endmill surface reduces welding
and allows stable machining. Achieves high precision machining with coating and sharp cutting edge.
Solid End MillRecommended Cutting Conditions
BQShouldering
Workpiece Materials Depth of Cut (apae) (mm) Outside Dia. (mm) 0.5 1 2 4 6 8 12 16
BQ BF Carbon Steel 1.2Dc0.05Dc Spindle Revolution (min-1) 32,000 25,500 13,200 6,600 4,500 3,300 2,200 1,700
(Dc<3) Feed Rate (mm/min) 210 225 230 375 415 420 410 410
Shouldering Alloy Steel Spindle Revolution (min-1) 27,000 22,000 11,000 5,600 3,700 2,800 1,900 1,400
1.2Dc0.1Dc Feed Rate (mm/min) 180 195 220 285 315 310 310 310
Slotting Pre-hardened Steel (Dc 3) Spindle Revolution (min-1) 22,500 12,700 7,200 4,200 3,000 2,200 1,500 1,100
30~45HRC Feed Rate (mm/min) 50 55 80 100 105 105 110 110
1.2Dc0.05Dc Spindle Revolution (min-1) 27,000 22,000 11,000 5,600 3,700 2,800 1,900 1,400
Stainless Steel (Dc<3) Feed Rate (mm/min) 60 95 95 110 115 115 115 115
1.2Dc0.1Dc
(Dc 3)
1.2Dc0.05Dc
(Dc<3)
1.2Dc0.1Dc
(Dc 3)
1.2Dc0.05Dc
(Dc<3)
1.2Dc0.1Dc
(Dc 3)
* Machining with coolant is recommended for stainless steel.
Please refer to page L44 about Slotting.
L12 : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru
www.kyocera-tools.ru