Kyocera - Основной каталог 2010-2011 ENG
T5u5r°nDiina mgoInndd/eNxe gaabtliev eI/nwsiдtлeяhrзаtкHаsзoа -lkeyocera@kyocera-tools.ru
(mm) (mm)
80°Diamond • Negative with Hole Description A T d Description A T d
CN_0903_ 9.525 3.18 3.81 CN_1204_ 12.70 4.76 5.16
CN_1204_ 12.70 4.76 5.16 CN_1606_ 15.875 6.35 6.35
B CN_1906_ 19.05 6.35 7.94
Negative P Free-cutting steel Classification of usage
$ Carbon Steel and Alloy Steel : Interruption / 1st Choice
% Ar M Stainless Steel
3 d : Interruption / 2nd Choice
4 Gray Cast Iron
5 K : Light Interruption / 1st Choice
7 Nodular Cast Iron
8 : Light Interruption / 2nd Choice
N
Non-ferrous Metals :Continuous / 1st Choice
80 T S Heat-resistant alloy : Continuous / 2nd Choice
Description
Titanium Alloy (In case hardness is under 45HRC)
H Hard Materials
PVD
Coated Carbide
Dim. TN6010CermetPVD
(mm) TN6020Cermet
TN60
PV7005
PV7010
PV7020
CA5505
CA5515
CA5525
CA5535
CA6515
CA6525
CA4010
CA4115
CA4120
CA4505
CA4515
PR930
PR1005
PR1025
PR1125
KW10 Carbide
Ref. Page for
Toolholder
CVD Coated Carbide
Insert Applicable
Chipbreaker Range
r
CNMG 120404 0.4 D8 (mm) (Steel / Edge Length=19)
120408 0.8 F42 10
120412 1.2 F66 Standard
120416 1.6 8
D8
Insert (Turning) CNMG 160608 0.8 ap 6 HX
Roughing 160612 1.2 D8
160616 1.6 F42 4
F66 HS
CNMG 190608 0.8
190612 1.2 D8 2
190616 1.6
190624 2.4 D8 0.2 0.4 0.6 0.8 1.0
F42 f (mm/rev)
CNMG 120408PH 0.8 F66
120412PH 1.2 (mm)
120416PH 1.6 D8 (Steel / Edge Length=12,16,19)
Roughing CNMG 160608PH 0.8 ap ap 12
160612PH 1.2 PH (19)
160616PH 1.6
10
CNMG 190608PH 0.8 PH (16)
190612PH 1.2
190616PH 1.6 8
190624PH 2.4
6
CNMM 120408PX 0.8
120412PX 1.2 4
120416PX 1.6 PH (12)
Roughing CNMM 160608PX 0.8 2
160612PX 1.2
160616PX 1.6 0.2 0.4 0.6 0.8 1.0
f (mm/rev)
CNMM 190608PX 0.8
190612PX 1.2 (mm)
190616PX 1.6 (Steel / Edge Length=12,16,19)
190624PX 2.4
12
PX (19)
10
PX (16)
8
6
4
2 PX (12)
0.2 0.4 0.6 0.8 1.0
f (mm/rev)
Single Sided / High Feed
CNMG 120404XP 0.4
120408XP 0.8
Finishing (mm)
5
(Low Carbon Steel)
CNMG 120404XP-T 0.4 4
120408XP-T 0.8
Finishing / Tough Edge
Low Carbon Steel 3
ap
D8 2 XS
F42 XP XQ
F66
1 XP-T
CNMG 120404XQ 0.4 0.1 0.2 0.3 0.4 0.5
120408XQ 0.8 f (mm/rev)
Medium
CNMG 120408XS 0.8
Roughing
For grades TN30 PV60 PR905 , See Page B40
PV30 PV90 PR915
Inserts are sold in 10 piece boxes.
B16 : Std. Item : Check Availability R : Std. Item (R-hand Only) kyLo:cSetrda.@Itekmyo(Lc-ehraan-dtoOonlsly.)ru
www.kyocera-tools.ru