Kyocera - Основной каталог 2010-2011 ENG

                                                              для заказа - kyocera@kyocera-tools.ru

         Product Lineup

         Product Lineup

                                            KTKF                   ( H6)                                                                    KTKFS              ( H8)
                                                               H12~H13)
         For Small          Toolholder                                                                      For sub spindle
         Diameter       (Long Shank for                                                                          tooling
          Cut-Off       Automatic Lathe)
                                                                                                                 Cut-Off Dia.
                              Cut-Off Dia.                                                                          6~12

                                 5~12
                                   ~16

                                            Width: 0.5~2.0 mm                                                                   Width: 1.0~2.0 mm

                                            KGM     (                     KGM-T             ( H13)

          CERACUT /     Bolt Clamp
         Plunge & Turn
                         Cut-Off Dia.
             (2-edge)
                           10~32
                           18~50

                                            Width: 1.5~4.0mm, 3~8mm       Width: 2.0~6.0mm

                                            KTKH-S             ( H16)                                           Toolholder      KTKH-B                          ( H16)
                                                                                                            (Long Shank for                                    ( H18)
                            Toolholder                                                                      Automatic Lathe)    Width: 1.6~3.1mm
                        (Long Shank for                                                                                         KTKB-S(S)
                        Automatic Lathe)                                                                        Bolt Clamp

                              Cut-Off Dia.                                                                        Cut-Off Dia.

H CERACUT               30~45                                                                                     10~32

            Cut-Off                         Width: 2.2~3.1mm   ( H16)
              (1-edge)                      KTKH-S

Cut-off                 Toolholder Type                                                                     Blade type

                             Cut-Off Dia.                                                                    Cut-Off Dia.

                               30~79                                                                        32~120

                                            Width: 2.2~5.1mm                                                                    Width: 1.6~9.6mm

         Cut-Off Tools

         Series Name    Shape                                       Advantage                                               Application

         For Small                                  1) Insert clamp is side screw type from lateral         1) For cut-off and grooving of small
         Diameter                                      side                                                    workpieces
          Cut-Off
                                                    2) 2-edge Insert                                        2) For automatic lathe, small machine
          CERACUT /                                 3) Ground Chipbreaker & No Chipbreaker
         Plunge & Turn                              4) Width: 0.5~2.0mm                                     1) For cut-off and grooving of small
                                                    5) Cut-off Diameter is prepared for two sizes              workpieces

                                                       from 5~12 and max.16.                             2) For automatic lathe, small machine
                                                    1) Insert is clamped from top side                      3) TMR-Chipbreaker provides stable chip
                                                    2) 1-edge and 2-edge inserts available
                                                    3) Molded Chipbreaker & No Chipbreaker Insert              control up to high feed rate ranges.
                                                    4) MT-Chipbreaker • • • Smaller Corner-R(r) 0.0, 0.05

                                                       TK-Chipbreaker • • • Larger Corner-R(r) 0.2~0.3
                                                       TMR-Chipbreaker • • • Corner-R(r) 0.2
                                                    5) Max. Cutting Dia.: 50

         CERACUT                                    1) Self-Clamping System                                 1) For cut-off and deep grooving
           Cut-Off                                     Tap the insert lightly with a plastic hammer         2) Standard chipbreaker is general cut-off
                                                       to set it in the pocket.
                                                                                                               type.
                                                    2) 1-edge insert                                              Feed rate : over 0.1mm/rev
                                                    3) Molded Chipbreaker
                                                                                                               P-Chipbreaker is for cut-off at low feed rates
                                                       • Standard (e.g.: TKN3)                                    Feed rate : 0 03~0.08mm/rev
                                                       • P-Chipbreaker (e.g.: TKN3-P)
                                                    4) Blade type and Integral Shank type
                                                    5) Max. Cutting Dia.: 120

H2                                                                   kyocera@kyocera-tools.ru
                                                                        www.kyocera-tools.ru