Kyocera - Основной каталог 2010-2011 ENG

                                                                             для заказа - kyocera@kyocera-tools.ru                                                                 CERACUT Plunge&Turn

          Face Grooving Toolholders

            KFMS-8

                                               D                                      T
                                                  (Face Grooving Dia)
                                                                                                               L1
                                                                                      F  L2
                                                                                         H2 h H3 W

                                                                                                                                                                H1 B

                                           T                                                                                                                             Left-hand Shown

                                                                    Right-hand Shown

          Toolholder Dimensions

                                                            Std.                       Dimension (mm)                     Width Face Grooving                                             Spare Parts        Ref. Page for
                                                                                                                                                                                                                Recommended
                                                                                                                          (mm) Dia. D                                             Screw Wrench                     Cutting Conditions

          Description

G                                                           R L H1=h H2 H3 B L1 L2 F T                                                                                W MIN. MAX.

          KFMS 2525M5464-8                                                        -                                                                                      54 64
                      2525M6382-8                                                                                                                                        (0) ( )
                      2525M80115-8                                                     9 41
                      2525M105160-8                                                                                                                                      63 82
                      2525M155510-8                                               2.4
                      3232P155510-8                                                                                                                                      (0) ( )
Grooving                                                                      25       25 150                      26 25                                              8  80 115

                                                                                  68           40                                                                        (0)  ()   HH6X25          LW-5      G76
                                                                                                                                                                         105  160

                                                                                                                                                                         (0) ( )

                                                                              25 6     25 150                      26                                                    155 510
                                                                              32 -                                                                                       (0) ( )
                                                                                       8 43 25                                                                        8

                                                                                       32 170                      33

          Dimension T shows available grooving depth.
          The value ( ) of Face Grooving Dia. (D Max) is the maximum outer diameter value after the initial groove between MIN MAX. (It is possible to widen the groove to infinity ).
          The value ( ) of Face Grooving Dia. (D Min) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial groove
          between MIN MAX.

          Applicable Inserts                                                                                              P Carbon Steel / Alloy Steel                                                       Classification of usage
                                                                                                                          M Stainless Steel
                    Description                 L           (mm)                                                          K Cast Iron                                                                            : Continuous-Light Interruption /
                                                                                                                          N Non-ferrous Metals                                                                    1st Choice
          GMM 8030-080MW                       30            H                                                            S Titanium Alloy                                                                       : Continuous-Light Interruption /
          GMG 8030-050MG                                                                                                                                                                                          2nd Choice
          GMGA 8030-400R                                    5.5                                                                  Hard materials (under 40HRC)                                                    : Continuous / 1st Choice
                                                                                                                                                                                                                 : Continuous / 2nd Choice
                                                                                                                          H
                                                                                                                                                                                                              Applicable
                                                                                                                                 Hard materials (over 40HRC)                                                  Toolholder

                                                                                                                          Dimension (mm)                                           Cermet   PVD                                                   Ref. Page for
                                                                                                                           W r M                                                      CVDCoated                                                     Toolholder
                                                                                                                                                                                          Carbide
                                                                                                                                                                                          Coated Carbide
                                                                                                (Previous
                                                                                              Description)                                                                                         Carbide

                                           Insert                                 Description                                                                                      TN90
                                                                                                                                                                                      CR9025
                                                                                                                                                                                          PR915
                                                                                                                                                                                              PR930
                                                                                                                                                                                                  PR905
                                                                                                                                                                                                      KW10

                                               M         22
                                                               W 0.05
                                                                              GMM 8030-080MW GMM 8030-08 8.0 0.8 6.0
                                               L                              GMG 8030-050MG GMG 8030-05MG 8.0 0.5 6.0
                                                                              GMGA 8030-400R GMGA 8030-40R 8.0 4.0 6.0
                                                         H

          Chip Control Oriented / M Class

                                           W 0.03     L                                                                                                                                                      KFMS 8 G68
                                                22
          Sharp-Cutting Oriented /         15
             Precision Class                                  M
                                                                           H
           Ground Chipbreaker

                                               M
                                                                    W 0.02
                                                   L

          Sharp-Cutting Oriented /                          H
             Precision Class
             Full-R / Copying

G68        Inserts are sold                                                                         : Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
          in 10 piece boxes.
                                                                                               kyocera@kyocera-tools.ru
                                                                                                  www.kyocera-tools.ru