Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru
Face Grooving Diameter Table
Specification Table of Shallow Grooving Insert (Depth 8.1 )
Type Width Depth Face Grooving Dia.D (mm) Reference
(mm) 250 Page
(mm) 6 8 20 30 50 70 100 150
TWFG (Lay-down Twin Bar) 0.5~2.0 1.0~3.0 6~ (Traversing is not available G54
TWFGT (Up-right Twin Bar) 0.5~2.0 1.0~3.0 6~ (Traversing is not available
VNFG (System Tip-Bar) 1.0~3.0 2.0~3.0 8~ (Traversing is not available G56
HPFG (2 Edges Tip-Bar) 1.0~3.0 2.0~3.0 8~ (Traversing is not available G53
PSFG-S (Tip-Bar) 1.0~3.0 2.0 8~ (Traversing is not available G57
GFVS-AA, GFVT-AA 1.0~3.0 2.2 8~ (ap has to be less than corner-R(r) when traversing with edge width 1.0mm G58
GFV 201A 2.0~3.4 2.2 20~ G60
KGMM 3.0 3.0~3.5 22~ G24
KGMS 4.0 4.0 28~
5.0 4.0 30~
GIFV 201A 2.0~3.4 2.2 35~ G70
GFV, GFVS, GFVT 351B 2.5~3.5 4.6 35~50
GIFV 352B 4.0~4.9 5.1 35~50 G60
501B 2.5~3.5 4.6 50~70 G62
GFV, GFVS, GFVT 502B 4.0~4.9 5.1 50~70 G70
GIFV 501C 3.5~4.5 6.6 50~70
502C 5.0~6.0 8.1 50~70
701B 2.5~3.5 4.6 70~100
G GFV, GFVS, GFVT 702B 4.0~4.9 5.1 70~100
701C 3.5~4.5 6.6 70~100
702C 5.0~6.0 8.1 70~100 G60
3.5~4.5 6.6 G62
GFV, GFVS, GFVT 1001C 5.0~6.0 8.1 100~150
1002C 100~150
Grooving GFV, GFVS, GFVT 1501C 3.5~4.5 6.6 150~250
1502C 5.0~6.0 8.1 150~250
Specification Table of Deep Grooving Insert (Depth 8.1 )
Toolholder Type Width Depth Face Grooving Dia.D (mm) Reference
(mm) (mm) Page
25 50 75 100 150 200 250 510
KFMS -3 13 25~30 G66
KFMS -4
3.0 22 30~ 40 G67
40~50 G68
25 50~65
12 65~85
20 85~110
110~145
4.0
25 25~35
35~50
KFMS -5 20 50~70
70~100
5.0 100~150
6.0 25 150~220
220~
KFMS -8 8.0 25
25~35
35~50
50~75
75~115
115~180
180~235
235~
54~64
63~82
80~115
105~160
155~510
Blade type Width Depth Face Grooving Dia.D (mm) Reference
KFTB -4S (mm) (mm)
KFTB -5S 25 50 75 100 150 200 250 510 Page
25
65~100
4.0 30
90~150
30
5.0 32 140~250
38 230~ G69
90~150
150~250
250~
G52 kyocera@kyocera-tools.ru
www.kyocera-tools.ru