Kyocera - Основной каталог 2010-2011 ENG

                                                  для заказа - kyocera@kyocera-tools.ru                                          CERACUT Plunge&Turn

GMN                                               Classification of usage                       P  Carbon Steel / Alloy Steel    KBN10B
                                                                                                M  Stainless Steel                       KBN510
                  Insert                          : Continuous-Light Interruption / 1st Choice  K  Cast Iron                                      KBN525
                                                  : Continuous-Light Interruption / 2nd Choice  N  Non-ferrous Metals                                     KPD001
                                                  : Continuous / 1st Choice                     S  Titanium Alloy                                                  KPD010
                                                  : Continuous / 2nd Choice                        Hard materials (under 40HRC)
                                                                                                H  Hard materials (over 40HRC)                                          Ref. Page for Toolholder

                                                                    Dimension (mm)                            Angle              CBN             PCD
                                                                                                               (°)

                                                  Description

                                                               W r M L H 

                                                  GMN 2        2.0  0.2                         1.8
                                                          3         0.4
                                                          4
                                SM22                      5    3.0  0.2                         2.3
                         Lr            W 0.05             6         0.4
                 S=2.9                                                                                                                                G22
                                                               4.0  0.2                         3.3  20  4.3  -                                       G23
                                                                    0.4                                                                               G24

                                  H                                 0.2
                                                                    0.4
                                                               5.0                              4.2

Deep Grooving                                                  6.0  0.2                         5.2                                                                                               G
     1-Edge                                                         0.4

                                                                                                   For recommended cutting conditions, see page G74

Available cutting diameter of KGM                                                                  130
(For automatic lathe) / KGM-T type                                                                                    40 (D: Cutting Dia.)

   There is a limit to available grooving depth depending                                                                                                                           Grooving
   on the workpiece diameter.                                                                                 20 (t: Available Groove Depth)

                                                                                                                 When the workpiece diameter becomes large, the available
                                                                                                                 cutting diameter becomes smaller due to interference with toolholder.

                                                                                                         e.g.) KGMR2525M-3T20+GMN3

KGM Available Cutting Diameter Table

     Toolholder                                                     D (Cutting Dia.)

KGM          0810K-1.5-125 - - - -                                                                            10 14 16 32

             1010K-1.5-125 - - - -                                  20 25 32 40 60

             1212F-1.5-85      -  -            -  - 25 26 28 32 36 40 60 100
             1212M-1.5-150

             0810K-2-125 - - - -                                                                              10 14 16 32

             1010K-2-125 - - - -                                    20 25 32 40 60

             1212F-2-85        -  -            -  - 25 26 28 50
             1212M-2-150

             1616M-2-150 32 40 50 60 80 100

             1010K-2.5-125 - - - -                                  20 25 32 40 60

             1212F-2.5-85      -  -            -  - 25 26 28 32 36 40 60 100
             1212M-2.5-150

             1616M-2.5-150 32 40 50 60 80 100

             1616M-3-150 32 40 50 60 80 100

Available Grooving Depth t (mm) 16 15 14 13 12.5 12 11 10 9 8 7 6 5 4 3 2                                                                     1

KGM-T Available Cutting Diameter Table (GMN, GM When using 1-edge insert)

     Toolholder                                              D (Cutting Dia.)

KGM          2012K-2T17        -  -                                                   66 80 130 260
             2020K-2T17        -  -                          40 54 70 100 180
             2525M-2T17
             1616H-3T20        -  -                          40 90 130 240
             2012K-3T20
             2020K-3T20
             2525M-3T20
             2020K-4T20

             2525M-4T20        -  - 50 140 240
             2525M-4T25        -  - 50 280 600
             2525M-5T25
             3232P-5T25

             2525M-6T30 100 300

Available Grooving Depth t (mm) 30 27 25 23 22 20 19 18 17 16 15 14 Under 13

: Std. Item    : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)                                                   CBN & PCD Inserts are

                                                                        kyocera@kyocera-tools.ru                                              G21sold in 1 piece boxes.
                                                                           www.kyocera-tools.ru