для заказа - kyocera@kyocera-tools.ru
CAUTION
Safety Notes of Cutting Tools
Precaution for using cutting tools
Target Products Precariousness Countermeasures
General Cutting Direct touch to a sharp cutting edge may cause injury. * When you set up tools to the machine or take tools out of the
case, please wear protective gloves.
Tools
* Please use safety items, such as safety glasses and protective
Misuse or inappropriate working conditions may cause tool gloves.
breakage or dispersion of broken pieces.
* Please use in the range of our recommended machining
condition. See our catalog or instruction manuals.
Excessive impact or heavy wear will increase cutting resistance * Please use safety items, such as safety glasses and protective
and may cause tool breakage and dispersion of broken pieces. gloves.
* Early exchanging tools is preffereable.
Dispersion of heated or prolonged chips may cause injury or * Please use safety items, such as safety glasses and protective
burn. gloves.
* For chips removal, please stop the machine beforehand and
use safety items, such as safety glasses and protective gloves.
Tools and materials become high temperature during cutting * Please prepare safety items, such as safety glasses and
operation. Direct touch to the tools and materials shortly after protective gloves.
machining may cause burn.
Sparks, generation of heat or chips in high temperature during * Please do not operate around Hazardous zone, in which there
operation may cause re. is some possibility of re or explosion.
* In case of using oil-coolant, please be sure of enough system
for re-prevention.
Lack of dynamic balance in high-speed revolution cause tool- * Please use safety items, such as safety glasses and protective
broken by vibration. gloves.
* Please conduct test-operation before cutting, and conrm that
there is no vibration or unusual sound.
Indexable Cutting Direct touch to burrs which were generated on the rough sur- * Do not touch workpiece with bare hand.
Tools face of the workpiece may cause injury.
* Please clean up insert pockets or clamping parts before setting
If inserts or parts are not installed well, falling off or dispersion insert.
of them may occur and cause injury.
* Please set up inserts with supplied wrench only, and conrm
that the inserts or parts are clamped completely. Never use
inserts or parts other than those prescribed.
If inserts are clamped too tightly by supplementary tools like * Do not use aids such as pipes. Please set up using supplied
pipe etc, inserts or body may be broken. wrench only.
When tools are used in high-speed revolution, inserts or parts * Please use in the range of our recommended machining
may burst out of the body due to centrifugal force. conditions.
For handling, please pay extra attention for safety. See our catalog or instruction manuals.
Milling Cutters Since milling cutters have sharp edges, direct contact with bare * Please use safety items, such as safety glasses and protective
and other Milling
hands may cause injury. gloves.
Tools
If a cutter lacks balance, tools would cause vibraion and it may * Please use in the range of our recommended machining
Drilling cause injury by dispersion of borken pieces. condition.
Brazed Tools
* Accuracy and balance of machine spindle should be checked
Others and adjusted regularly to prevent from eccentric rotation or run
out due to wear of bearing portion.
When drilling through hole with running work, a disc sometimes * Please use safety items, such as safety glasses and protective
ies out from the end of frilling with high speed. This is very gloves.
dangerous since the disc has sharp edge. Also attach a cover on a chuck part.
Dispersion of broken inserts or falling off may cause injury. * Please check chips are brazed rmly before use.
* Please do not use brazed tools in the condition that requires
high cutting temperature.
If brazing is carried out many times, the strength of carbide insert * Please do not use tools which are brazed several times. Since
is deteriorated and becomes easy to be broken during cutting. tool strength have been deteriorated.
It is dangerous to use tools except for the xed application. It * Please keep our recommended usage of tools.
may damage tools and machines.
kyocera@kyocera-tools.ru 3
www.kyocera-tools.ru
