Kyocera - Основной каталог 2010-2011 ENG

                                                                     для заказа - kyocera@kyocera-tools.ru

Face Grooving G49-G71                                                                          For Face Grooving Diameter Table See Page G52

                    VNFG                       ( G56) HPFG           ( G53)                                 STW                 ( G55) S..-STW            ( G55)
                                                             PSFG-S  ( G57)
   Face
Grooving
(Small Dia.)

   (Solid

Face Grooving Dia. Depth: 2.0, 3.0mm              Depth: 2.0, 3.0mm HPFG                 Micro Face         Depth: 1.0~3.0mm            Depth: 1.0~3.0mm
          8~ Width: 1.0, 2.0, 3.0mm              Width: 1.0, 2.0, 3.0mm                  Grooving          Width: 0.5~2.0mm            Width: 0.5~2.0mm

                    GFVS-AA                    (  G58) GFVT-AA       ( G58)                                 STWS                ( G55)

Face

Grooving

(Small Dia.)

(2-Edge)

Face Grooving Dia. Depth: 2.2mm                   Depth: 2.0mm                           Face Grooving Dia. Depth: 1.0~3.0mm
          8~ Width: 1.0, 2.0, 3.0mm              Width: 1.0, 2.0, 3.0mm                           6 - Width: 0.5~2.0mm

  Face              GFV                        ( G60) GFVS           ( G62) GFVT               ( G62) GIFV                      ( G70)
Grooving
 (General                                                                                                                                                         G

purpose)

(2-Edge)

 For face grooving                                Depth: 4.6~8.1mm           Depth: 4.6~8.1mm               Depth: 2.2~8.1mm
dia. see each page. Depth: 2.2~8.1mm              Width: 2.5~6.0mm           Width: 2.5~6.0mm               Width: 2.0~6.0mm

                             Width: 2.0~6.0mm

                      KFMS                     ( G66) KFMS-8         ( G68)                                 KFTB-S              ( G69)

Grooving /                                                                                                                                                        Grooving

Plunge&Turn

(Grooving / Multi-

Function)

 For face grooving                                Depth: 25.0mm                                             Depth: 25.0~38.0mm
dia. see each page. Depth: 13.0~32.0mm            Width: 8.0mm                                              Width: 4.0, 5.0mm

                             Width: 3.0~6.0mm

PR1115 : PVD Coated Carbide for Steel

1. Micro-grain carbide improves its bending strength better
   than conventional carbide!

2. New Fine Surface PVD Coating improves wear and chip-
   ping resistance!

3. Supports wide range for continuous / interrupted cutting
   with middle~high speed

Coating layer of PR1115                                              Performance            High
          Sectional Structure                                                              Speed
                                                                                         [150m/min]
                            NEW FS(Fine Surface) Coat       • High hardness (30GPa)                                    PR1115
                            (TiAlN)                                                        Middle                 PR930
                            Suitable for high speed ma-     • High Adhesive Strength       Speed
                            chining, and excellent in wear                               [100m/min]         Continuous Low Interrupted
                            resistance                      • Precise, ne texture
                            Micro-grain carbide substrate                                   Low
                                                            • High oxidation resistance    Speed
                                                             (800°C)                     [50m/min]

NEW FS (Fine Surface) coating (TiAIN)                                                                                                   Interrupted

Newly developed TiAIN PVD coat brings stability and smooth machining.
coating layer hardness / adhesive strength better than conventional FS
coating

PR905: PVD Coated Carbide for Cast Iron

1. High efciency and stability made possible during machining of gray cast iron /

   nodular cast iron
2. Long life is made possible with TiAIN coating, bringing smooth insert surface,

   wear resistance, and, high temperature stability
3. Special carbide substrate made of hard material with excellent plastic

   deformation performance reduces edge wear

                                                                     kyocera@kyocera-tools.ru                                                                     G3
                                                                        www.kyocera-tools.ru