Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.r[uSolid Tip-Bars for Micro Boring]
SVN Square Shank (Straight) SVNS Square Shank (L-shape)
Side Stopper
L2
Side Stopper
Note 2 F1 L2 H1 B F2 H1 B
F1
F3 1
Note 1 L1
L4 L3 L1
h
h
Fig.1 (SVN) Fig.2 (SVNS)
Right-hand shown R-hand Insert for R-hand Toolholder.
Note 1 & Note 2 : For insert dimensions, see page F10~F11
Toolholder Dimensions
Dimension (mm) Spare Parts Applicable Inserts F
Drawing Clamp Screw Wrench Screw Wrench F10~F11
G33
(Side Stopper) G56
J27
Description Std. H1=h B L1 L2 L3 L4 F1 F2 F3 FT
LTW
SVNR 1010H -12 10 10 100 10 HS3 4 VNBR - Boring
1212K -12
1616K -12 12 12 12 - - Fig.1 SB-3080TR FT-10 HS3 8 VNBTR -
2020K -12 HS3 12
2525M -12 16 16 125 22 - - 16 HS3 16 LW-1.5 VNGR -
LW-1.5
SVNSR 1010K-12-06 20 20 20 29 6 LW-1.5 VNFGR -
1 0 1 0 K -12-11 25 25 150 25 LW-1.5 VNTR -
(VNBR 06- )*
1212M -12-06 10 10 125 10 12 10 (VNBR 11- )*
(VNBTR
1212M -12-11 10 10 125 45 10 12 10 33 11 SB-3080TR LTW-10S HS3 4 (VNGR 11- )*
(VNTR -11)*
1212M -12-20 12 12 150 10 12 12 29 6 (VNBR
1616M -12-06 (VNBR -11)*
12 12 150 10 12 12 33 11 (VNBTR
1616M -12-11 (VNGR 06- )*
45 SB-3080TR LTW-10S HS3 4 (VNTR 11- )*
1616M -12-20 (VNBR
12 12 150 10 12.5 12 Fig.2 (VNBTR 11- )*
16 16 150 16 12 16 42 20 (VNGR -11)*
(VNBR
29 6 (VNBR -11)*
(VNBTR 20- )*
16 16 150 16 12 16 33 11 (VNGR
(VNTR 20- )*
45 SB-3080TR LTW-10S HS3 4 (VNBR -20)*
(VNBTR
16 16 150 16 12.5 16 42 20 (VNGR 06- )*
11- )*
11- )*
-11)*
-11)*
20- )*
20- )*
-20)*
All System Tip-Bar Inserts are used with a SVNSR Toolholder, however, When setting the cutting edge at the face level of the toolholder as shown in Fig.2, use the insert shown in ( ).
In these cases, the F3 dimension of the toolholder corresponds to the L2 dimension of the insert.
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru F13
www.kyocera-tools.ru