Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru Top Clamp
External Toolholders [SP R, SP N Insert]
CSBP (External) CSKP (Facing)
Side Rake Angle: +6° 75 75 Side Rake Angle: +6°
Angle of Inclination: +0° L2 Angle of Inclination: +0°
F1 L1 H1 B
h H3 F2
H1 B
h H3 F1
75
L2
L1
75
Right-hand shown Right-hand shown
E CSDP (External / Chamfering)
CSSP (External / Facing / Chamfering) Side Rake Angle: +4° 15'
Angle of Inclination: +4° 15'
Side Rake Angle: -09 type +5°
Side Rake Angle: -12 type +6°
Angle of Inclination: 0°
Small Tools H3 F1 H1 B h H3 F1 45 H1 B
45 F2
L2 Standard Corner-R(r) L2
L1 L1
45 45
45 h
Right-hand shown
Toolholder Dimensions
Std. Dimension (mm) Spare Parts
Clamp Set Wrench Shim Shim Screw Chipbreaker
Description
R N L H1=h H3 B L1 L2 F1 F2
CSBP 1212F -09N 12 7.5 12 80 23 15.7 13 0.4 CPS-2P LW-2.5 -- CB-S3220
LW-2.5 -- CB-S3220
CSKP 1616H -09N 16 7.5 16 100 21 20 - 0.4 CPS-2P LW-3
KPS-42 SP3X8 CB-S4220
2020K -12N 20 20 125 25 LW-2.5
2525M -12N 8.5 28 - 0.8 CPS-3
25 25 150 32 LW-3
CSSP 1212F -09N 12 12 80 15 16 9 LW-3 - - CB-S3220
1616H -09N 7.5 0.4 CPS-2P
16 16 100 16 20 13
2020K -12N 20 20 125 25 16
2525M -12N 8.5 19 0.8 CPS-3 KPS-42 SP3X8 CB-S4220
25 25 150 32 23
CSDPN 2020K -12N 20 20 125 10
2525M -12N 8.5 32 - 0.8 CPS-3 KPS-42 SP3X8 CB-S4220
25 25 150 12.5
Chipbreaker is not included. Purchase separately.
Applicable Inserts Medium cutting Medium cutting Finishing-Medium Cast Iron Cast Iron Non-ferrous Metals Hard Materials
B58 B58
Applications B58 B58 B88 C23 C15
Ref. Page G Standard Without Chipbreaker Ceramic
PCD CBN
Insert
Toolholder
CSBP ...-09N SPMR0903.. SPMR0903.. SPGR0903.. SPMN0903.. SPGN0903.. - SPGN0903..
SPGN0903..
CSKP ...-09N SPMR0903.. SPMR0903.. SPGR0903.. SPMN0903.. SPGN0903.. - SPGN0903..
SPGN0903.
CSKP ...-12N SPMR1203.. SPMR1203.. SPGR1203.. SPMN1203.. SPGN1203.. SPGN1203.. SPGN1203..
SPGN1203..
CSSP ...-09N SPMR0903.. SPMR0903.. SPGR0903.. SPMN0903.. SPGN0903.. - SPGN0903..
SPGN0903..
CSSP ...-12N SPMR1203.. SPMR1203.. SPGR1203.. SPMN1203.. SPGN1203.. SPGN1203.. SPGN1203..
SPGN1203..
CSDPN...-12N SPMR1203.. SPMR1203.. SPGR1203.. SPMN1203.. SPGN1203.. SPGN1203.. SPGN1203..
SPGN1203..
CSKP : L-hand Insert for R-hand Toolholder. For recommended cutting conditions,
CSSP : At External Turning, R-hand Insert for R-hand Toolholder, L-hand Insert for L-hand Toolholder. see page E30~E31
At Facing, L-hand Insert for R-hand Toolholder, R-hand Insert for L-hand Toolholder.
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
E28 kyocera@kyocera-tools.ru
www.kyocera-tools.ru