Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru Wedge Lock
WTJN (External / Copying) F1 93 L2 L1 H1 B Side Rake Angle: -6°
h F2 4.5 20 Angle of Inclination: -6°
3 WTJNR/L2020K types,
Right-hand shown 15 Shim Nut sticks out as shown
below.
WTKN (External / Facing / Copying) F1 L2 15 H1 B External
h F2 L1 4.5 20 D
15
15 Side Rake Angle: -6°
Angle of Inclination: -6°
Right-hand shown WTKNR/L2020K types,
Shim Nut sticks out as shown
WTEN-N (External / Chamfering) below.
h F1 30 H1 B Back Rake Angle: -8.5°
Standard Corner-R(r)L2 L1 4.5 20 WTENNR/L2020K types,
Shim Nut sticks out as shown
below.
30
Toolholder Dimensions
Std. Dimension (mm) Clamp Set Shim Spare Parts Spacer
R N L H1=h B L1 L2 F1 F2
Shim Pin Shim Nut Wrench
Description
WTJN 2020K -16N 20 20 125 32 25 24
WTKN 2525M -16N 25 25 150 32
WTENN WTN-33
2020K -16N 20 20 125 32 25 - 0.8 WCS-1N *WTN WP-1S WN-1 LW-3 WSP-1
2525M -16N 25 25 150 32 30
2020K -16N -33-20
2525M -16N 20 20 125 10 -
25 25 150 32 12.5 -
• When using inserts whose corner R(r) is greater than 1.6mm, please purchase a shim with * mark and use it in order to prevent workpiece and shim from interfering each other.
Applicable Inserts
Toolholder Description Application Finishing Finishing-Medium Finishing-Medium Finishing-Medium Medium-Roughing Medium-Roughing Medium-Roughing Medium-Roughing• Medium-Roughing•
High Feed Rate High Feed Rate
GP HQ CQ TK GS PS HS PT GT
WTJN ...-16N A Insert
TN G
M 1604.. Size 1104,16 1104,16 16,22 16 1104,16 16,22 16,22 16 16
WTKN ...-16N TN Page B28
TN Application Roughing B28 B28 B28 B28 B28 B29 B29 B29
WTENN...-16N PH One side / Roughing• Roughing Finishing-Roughing Finishing-Roughing Medium-Roughing / Soft Steel Finishng Soft Steel / Medium cutting Soft Steel / Roughing
High Feed Rate Low Cutting Resistance type
PX Standard -S - -25R XP(-T) XQ XS
Insert
Size 16,22 16,22 16,22 1104,16 1103,1104,16,22 16 16 16 16
B29 B29 B29
Page Cast Iron Cast Iron Cast Iron B32 B32 B32 B29 B30 B30
C ZS GC
Application Stainless Finishing Stainless Medium Stainless Medium Stainless Medium Cast Iron Cast Iron Non-ferrous Metals Non-ferrous Metals Non-ferrous Metals Hard Materials
to Roughing to Roughing to Roughing
MQ MS MU TK Without Chipbreaker Ceramic AH -A3 PCD CBN
Insert
Size 16 16 16 16 16 16 16 1103,16,22 16 16 16 16 16
Page B30 B30 B30 B30 B31 B31 B31 B31 B86 B31 B31 C17 C7
• In wedge lock, use of ceramic insert other than TN30 / PV30 and silicon
nitride insert is not recommended due to strong restraint force. For recommended cutting conditions, see page D39~D40
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only) D15
kyocera@kyocera-tools.ru
www.kyocera-tools.ru