Kyocera - Основной каталог 2010-2011 ENG
для заказа - kyocera@kyocera-tools.ru Lever Lock
PDJN (External / Copying)
32 Side Rake Angle: -6°
Angle of Inclination: -7°
F1 H1 B
h F2 Applicable Inserts
Toolholder Description
93 L2 L1 DN A
DN G
PDJN ...-11 1104..
3 PDJN ...-15 DN A 1504..
Right-hand shown
PDJN ...-15U DN G 1506.. D
DN M (1504..)
PDHN (External / Face Grooving / Copying)
17.5 Side Rake Angle: -6° External
Angle of Inclination: -6°
Applicable Inserts
17.5
F1 Standard Corner-R(r)
h F2 17.5 Toolholder Description
L2 L1 H1 B
17.5 DN A 1504..
(1506..)
PDHN ...15 DN G
DN M
Right-hand shown
Std. Dimension (mm) Lever Lock Screw Spare Parts Wrench
Shim Shim Pin Punch
Description FH
R L H1=h B L1 L2 F1 F2
LW
PDJN 1616H -11 16 16 100 20 -
2020K -11
2525M -11 20 20 125 28 25 - 0.4 LL-1DN LS-1N LD-32N LSP-1 PC-1 FH-2.5
2020H -15* PC-2 LW-3
2020K -15 25 25 150 32 27 PC-2 LW-3
2525M -15
3225P -15 20 20 100 25 -
2525M -15U 20 20 125 36 25 - 0.8 LL-3N LS-2N LD-42 LSP-2
25 25 150 32 25 *LD-42-20
3232P -15U
32 25 170 32 25
25 25 150 32 25 LD-42
36 0.8 LL-4 LS-3 *LD-42-20 LSP-2
32 32 170 40 28
(LD-43)
(*LD-43-20)
PDHN 2020K -15 20 20 125 25 22 LD-43
2525M -15 36 0.8 LL-4 LS-3 *LD-43-20 LSP-2 PC-2 LW-3
25 25 150 32 24
(LD-42)
(*LD-42-20)
* mark indicates short shank type.
Shim: PDJN -15U ...LD-42 is attached to PDJNR / L-15U. When using DN 1504 type insert, prepare LD-43 separately.
PDHN ...LD-43 is attached to PDHN. When using DN 1506 type Insert, prepare LD-42 separately.
When using inserts whose corner R(r) is greater than 1.6mm, please purchase a shim with * mark and use it in order to prevent workpiece and shim from interfering each other.
Applicable Inserts
Application Finishing Finishing- Finishing- Finishing- Finishing- Medium- Medium- Medium-Roughing Roughing Roughing Roughing
GP Medium Medium Medium Medium Roughing Roughing PT GT Standard PH
HQ CQ CJ TK GS PS
Insert
Size 1104,1504,1506 1104,1504,1506 1504,1506 1504,1506 1506 1104,1504,1506 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506
B19 B20 B21
Page B19 B19 B19 B19 B20 B20 B20 B20
Finishing Medium Soft Steel Soft Steel / Soft Steel / Stainless Steel
Application One side / Roughing• -S Finishing Medium cutting Roughing Stainless Finishing Stainless Medium to Stainless Medium to
High Feed Rate XP -T GU
XQ XS Roughing Roughing
PX MQ MS MU
Insert
Size 1504,1506 1104 1104,1504 1504 1504 1504 1504,1506 1504,1506 1504,1506 1504,1506
Page B21 B21 B21 B22 B22 B22 B22
B21 B23 B23 Cast Iron Cast Iron Cast Iron
Application ZS GC Ceramic Non-ferrous Metals Non-ferrous Metals Non-ferrous Metals Hard Materials
Stainless Steel Stainless Medium Cast Iron
to Roughing
-ST TK C AH -A3 PCD CBN
Insert
Size 1506 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506 1504,1506 1504 1504 1504,1506
Page B22 B22 B23 B23 B23 B82 B23 B23 C17 C6
For recommended cutting conditions, see page D39~D40
: Std. Item : Check Availability R : Std. Item (R-hand Only) L : Std. Item (L-hand Only)
kyocera@kyocera-tools.ru D11
www.kyocera-tools.ru