для заказа - kyocera@kyocera-tools.ru
RECOMMENDED CUTTING CONDITIONS
R ecommended Cutting Conditions (TKF12/16 Inserts)
Workpiece Recommended Grade (Vc sfm) TKF12 TKF16
Material Width Width
Notes
MEGACOAT MEGA PVD DLC Carbide 0.020" 0.028" 0.039" 0.049" 0.059" 0.079" 0.059" 0.079"
NANO COAT Coated (0.50mm) (0.70mm) (1.00mm) (1.25mm) (1.50mm) (2.00mm) (1.50mm) (2.00mm)
Carbide
PR1425 PR1535 PR1225 PR1025 PDL025 KW10 Feed Rate (ipr) Feed Rate (ipr)
Carbon - - 0.0004~0.0008 0.0004~0.0012 0.0004~0.0016 0.0004~0.0016 0.0004~0.0016 0.0004~0.0016 0.0008~0.0028 0.0008~0.0028
Steel 225~550 230~500 225~500 200~425 (0.0004~0.0020) (0.0008~0.0039) (0.0008~0.0039) (0.0008~0.0039) (0.0008~0.0039)
(175~450) (160~400) (175~400)
Alloy - - 0.0004~0.0008 0.0004~0.0012 0.0004~0.0016 0.0004~0.0016 0.0004~0.0016 0.0004~0.0016 0.0008~0.0028 0.0008~0.0028
Steel 225~550 230~500 225~500 200~425 (0.0004~0.0020) (0.0008~0.0039) (0.0008~0.0039) (0.0008~0.0039) (0.0008~0.0039)
(175~450) (160~400) (175~400)
Stainless - - 0.0002~0.0006 0.0004~0.0008 0.0004~0.0008 0.0004~0.0008 0.0004~0.0008 0.0004~0.0008 0.0004~0.0016 0.0004~0.0016 Wet
Steel 200~450 200~400 200~400 175~325 (0.0004~0.0012) (0.0004~0.0020) (0.0004~0.0020) (0.0004~0.0020) (0.0004~0.0020)
(125~400) (130~330) (125~325)
Cast Iron - - - - - 0.0004~0.0012 0.0004~0.0016 0.0004~0.0020 0.0004~0.0020 0.0004~0.0020 0.0004~0.0020 0.0008~0.0032 0.0008~0.0032
175~325
Aluminum - - - - 0.0004~0.0012 0.0004~0.0016 0.0004~0.0020 0.0004~0.0020 0.0004~0.0020 0.0004~0.0020 0.0008~0.0032 0.0008~0.0032
660~1640 650~1475
Brass - - - - 0.0004~0.0012 0.0004~0.0016 0.0004~0.0024 0.0004~0.0024 0.0004~0.0024 0.0004~0.0024 0.0008~0.0039 0.0008~0.0039
325~650
Values in parentheses ( ) are cutting conditions for tough edge inserts style TKF..T.. : 1st Recommendation : 2nd Recommendation
R ecommended Cutting Conditions (GMM-MT / GMM-TK / GMM-NB Inserts)
Recommended Grade (Vc sfm) Width
Workpiece CVD PVD Carbide 0.059" 0.079"~0.098" 0.118" 0.158" Notes
Material Coated Carbide Coated Carbide (1.5mm) (2.0mm~2.5mm) (3.0mm) (4.0mm)
CR9025 PR915 PR930 KW10 Feed Rate (ipr)
Carbon Steel - 0.0004~0.0016 0.0008~0.0059 0.0012~0.0079 0.0032~0.0118
250~600 200~500 200~425
Alloy Steel - 0.0004~0.0016 0.0008~0.0059 0.0012~0.0079 0.0032~0.0118
225~500 200~500 200~425
Stainless Steel - 0.0004~0.0012 0.0008~0.0039 0.0012~0.0059 0.0032~0.0098 Wet
200~450 175~450 175~400
Cast Iron - - - 0.0004~0.0020 0.0020~0.0047 0.0039~0.0098 0.0039~0.0118
175~325
CUT-OFF
H Aluminum - - - 0.0004~0.0020 0.0020~0.0039 0.0020~0.0079 0.0020~0.0098
650~1475
Brass
- - - 0.0004~0.0020 0.0020~0.0039 0.0020~0.0059 0.0020~0.0079
325~650
• When using PR930, decrease the feed rate by 20% : 1st Recommendation : 2nd Recommendation
R ecommended Cutting Conditions (TKN / TK§ Inserts)
Recommended Grade (Vc sfm) Width
Workpiece Cermet CVD MEGACOAT PVD Carbide 1.6mm 2.0~2.4mm 3.1mm 4.1mm 4.8~9.6mm Notes
Material Coated NANO Coated Carbide KW10
Carbide PR660 PR930
TN620 TN90 CR9025 PR1535 Feed Rate (ipr)
Carbon Steel - 0.0008~0.0032 0.0016~0.0071 0.0020~0.0098 0.0032~0.0118 0.0059~0.0157
Alloy Steel 200~660 400~650 250~600 200~490 200~425 200~425
Stainless Steel - 0.0008~0.0032 0.0016~0.0071 0.0020~0.0098 0.0032~0.0118 0.0059~0.0157
Cast Iron
Aluminum 20~530 325~525 225~500 200~490 200~425 200~425 - 0.0008~0.0012 0.0016~0.0047 0.0020~0.0071 0.0032~0.0098 0.0039~0.0118 Wet
Brass 0.0008~0.0032 0.0020~0.0047 0.0039~0.0098 0.0039~0.0118 0.0059~0.0138
0.0008~0.0039 0.0020~0.0039 0.0020~0.0079 0.0020~0.0098 0.0039~0.0787
200~490 250~500 200~450 160~390 175~400 200~450 175~325 0.0008~0.0039 0.0020~0.0039 0.0020~0.0059 0.0020~0.0079 0.0039~0.0787
- - -
325~1475
- - -
- - - 325~650
: 1st Recommendation : 2nd Recommendation
R ecommended Cutting Conditions (GMM-TMR Inserts)
Workpiece Vc (sfm) Notes
Material 200~650
Carbon Steel
Alloy Steel 225~500 0.003~0.007 Wet
Stainless Steel 175~450
H32 kyocera@kyocera-tools.ru
www.kyocera-tools.ru