для заказа - kyocera@kyocera-tools.ru
CUT-OFF TOOLHOLDERS
KGD (Small Diameter Cut-Off) Insert Width : 0.059"~0.157" (1.3mm~4.0mm)
Insert Seat Angle F L2 H1 B
W
Insert Seat Angle H1 H3 H3
h
H4
A Dmax H2
Right-hand Shown L1
T oolholder Dimensions
Stock Cut-Off Dimensions Angle Insert Width Spare Parts
Dia.
( ° ) W Clamp Screw Wrench
Part Number Unit
RL Dmax H1=h H2 H3 H4 B L1 L2 F A MIN MAX
KGD§ 6-1.5JX 0.787 0.375 0.098 0.177 0.315 0.375 4.75 0.709 0.351 0.047 1° - 0.059 SB-40120TR LTW-15S
8-1.5JX 0.944 0.500 0.051 0.177 0.394 0.500 4.75 0.768 0.476 0.047 1° - 0.059
KGD§ 6-2JX 0.787 0.375 0.098 0.177 0.315 0.375 4.75 0.709 0.342 0.067 1° 0.078 0.118
8-2JX 0.944 0.500 0.051 0.177 0.394 0.500 4.75 0.768 0.467 0.067 1° 0.078 0.118 SB-40120TR LTW-15S
10-2JX 1.259 0.625 - 0.177 0.394 0.625 4.75 0.965 0.592 0.067 1° 0.078 0.118
KGD§ 6-2.4JX 0.787 0.375 0.098 0.177 0.315 0.375 4.75 0.709 0.336 0.079 1° 0.094 0.118
8-2.4JX inch 0.944 0.500 0.051 0.177 0.394 0.500 4.75 0.768 0.461 0.079 1° 0.094 0.118 SB-40120TR LTW-15S
10-2.4JX 1.259 0.625 - 0.177 0.394 0.625 4.75 0.965 0.586 0.079 1° 0.094 0.118
KGD§ 8-3JX 0.944 0.500 0.051 0.177 0.394 0.500 4.75 0.768 0.453 0.094 1° 0.118 0.118 SB-40120TR LTW-15S
10-3JX 1.259 0.625 - 0.177 0.394 0.625 4.75 0.965 0.578 0.094 1° 0.118 0.157
KGD§ 10-3D38JX 1.496 0.625 - 0.236 0.394 0.625 4.75 1.142 0.578 0.094 1° 0.118 0.157
12-3D42JX 1.653 0.750 - 0.236 0.551 0.750 4.75 1.220 0.703 0.094 1° 0.118 0.157 SE-50125TR LTW-20
43-3D42JX 1.653 0.750 - 0.236 0.551 0.500 4.75 1.220 0.453 0.094 1° 0.118 0.157
KGD§ 1010JX-1.3 20 10 2 4.5 8 10 120 18 9.5 1.0 5° 1.3 1.3
1212JX-1.3 24 12 2 4.5 10 12 120 19.5 11.5 1.0 5° 1.3 1.3
H KGD§ 1010JX-1.5CUT-OFF 20 10 2 4.5 8 10 120 18 9.4 1.2 5° 1.5 1.5 SB-40120TR LTW-15S
24 12 2 4.5 10 12 120 19.5 11.4 1.2 5° 1.5 1.5
1212JX-1.5
KGD§ 1212F-1.3 24 12 2 4.5 10 12 85 19.5 11.5 1.0 5° 1.3 1.3
1212F-1.5 24 12 2 4.5 10 12 85 19.5 11.4 1.2 5° 1.5 1.5
KGD§ 1010JX-2 20 10 2 4.5 8 10 120 18 9.15 1.7 1° 2.0 3.0
1212JX-2 24 12 2 4.5 10 12 120 19.5 11.15 1.7 1° 2.0 3.0 SB-40120TR LTW-15S
1616JX-2 32 16 - 4.5 10 16 120 24.5 15.15 1.7 1° 2.0 3.0
KGD§ 1010JX-2.4 mm 20 10 2 4.5 8 10 120 18 9 2.0 1° 2.4 3.0
1212JX-2.4 24 12 2 4.5 10 12 120 19.5 11 2.0 1° 2.4 3.0 SB-40120TR LTW-15S
1616JX-2.4 32 16 - 4.5 10 16 120 24.5 15 2.0 1° 2.4 3.0
KGD§ 1212JX-3 24 12 2 4.5 10 12 120 19.5 10.8 2.4 1° 3.0 3.0 SB-40120TR LTW-15S
1616JX-3 32 16 - 4.5 10 16 120 24.5 14.8 2.4 1° 3.0 4.0
KGD§ 1212F-2 24 12 2 4.5 10 12 85 19.5 11.15 1.7 1° 2.0 3.0 SB-40120TR LTW-15S
1212F-2.4 24 12 2 4.5 10 12 1° 2.4 3.0
85 19.5 11 2
KGD§ 1616JX-3D38 38 16 - 6 10 16 120 29 14.8 2.4 1° 3.0 4.0
2012JX-3D42 42 20 - 6 14 12 120 31 10.8 2.4 1° 3.0 4.0 SE-50125TR LTW-20
2020JX-3D42 42 20 - 6 14 20 120 31 18.8 2.4 1° 3.0 4.0
• Note ) 1.4mm width insert can be installed in KGD§1212JX-3, but is not recommended due to the toolholder's rigidity. Recommended Cutting Conditions H20~H21
• Recommended tightening torque for clamp screw is 2.0Nm for SB-40120TR and 2.5Nm for SE-50125TR
• When machining material greater than 36mm with KGD§...-3D38 or KGD§...-3D42 toolholders, use 1-edge inserts.
• Max. workpiece diameter for 2-edge inserts 36mm
Applicable Inserts Others
T oolholder Indentification System (Small Diameter) GDM/GDMS D38: Dmax 38mm
Edge Width: 3~4mm
KGD R 1616 JX - 3 D38
KGDS 1.3 B
Toolholder Shank Size Toolholder Applicable Inserts Others
Hand 1616mm Length B : For sub spindle tooling
120mm GDM/GDMS
R: ight-hand Edge Width: 1.3mm
L : Left-hand
kyocera@kyocera-tools.ru
H14 www.kyocera-tools.ru : U.S. Stock : U.S. Stock (R-hand Only) : U.S. Stock (L-hand Only)
: World Express (Shipping: 7-10 Business Days) : World Express (R-hand Only) : World Express (L-hand Only)