для заказа - kyocera@kyocera-tools.ru
RECOMMENDED CUTTING CONDITIONS
G A (Molded Chipbreaker)
Recommended Insert Grade (Vc sfm) f (feed) during Grooving (ipr)
f (feed) during Traversing (ipr)
Workpiece Cermet CVD PVD Carbide D.O.C. during Traversing (in) Notes
Material
TN60
TN90 GA 30 GA 40 GA 50
TC40
TC60M 0.0024~0.0071
CR9025 0.0020~0.0059
PR630 MAX 0.031
PR930 0.0024~0.0059
KW10 0.0020~0.0047
MAX 0.012
0.0024~0.0039 0.0024~0.0083 0.0024~0.0098
0.0020~0.0031
Carbon Steel 430~660 - - - 260~590 - - - MAX 0.031 0.0020~0.0067 0.0020~0.0079
MAX 0.039 MAX 0.051
0.0024~0.0071 0.0024~0.0087
Alloy Steel 330~590 - - - 260~520 - - - 0.0020~0.0059 0.0020~0.0071 Wet
MAX 0.020 MAX 0.031
0.0024~0.0039 0.0024~0.0047
Stainless Steel - - - - 200~430 - - - 0.0020~0.0031 0.0020~0.0039
MAX 0.031 MAX 0.047
G IA (Molded Chipbreaker) : 1st Recommendation : 2nd Recommendation
Recommended Insert Grade (Vc sfm) f (feed) during Grooving (ipr)
f (feed) during Traversing (ipr)
Workpiece Cermet CVD PVD Carbide D.O.C. during Traversing (in) Notes
Material
TN60
TN90 GIA 30 GIA 40 GIA 50
TC40
TC60M
CR9025
PR630
PR930
KW10
Carbon Steel - - - - - - 0.0016~0.0031 0.0016~0.0035 0.0020~0.0039
0.0008~0.0031 0.0008~0.0031 0.0020~0.0031
200~390 200~390 MAX 0.012 MAX 0.016 MAX 0.020
0.0016~0.0028 0.0016~0.0028 0.0020~0.0031
Alloy Steel - - - - - - 0.0008~0.0028 0.0008~0.0028 0.0020~0.0031 Wet
MAX 0.012 MAX 0.016 MAX 0.020
200~330 200~330 0.0016~0.0028 0.0016~0.0028 0.0020~0.0031
0.0008~0.0028 0.0008~0.0028 0.0020~0.0031
Stainless Steel - - - - - - - MAX 0.012 MAX 0.016 MAX 0.020
200~260
GROOVINGG P SG-S (Micro Bars) : 1st Recommendation : 2nd Recommendation
Recommended Insert Grade (Vc sfm) PSG05 PSG06 Note for using the grooving Micro-Bars PSG-S type
PSG07 How to Install
Workpiece PVD Carbide ~0.0012 PSG08 Internal small dia. grooving requires accurate installationNotes
Material ~0.0008 because an error of insert height or angle can affect the
~0.0020 ~0.0020 machining precision. When installing, set the cutting edge
PR630 KW10 Feed Rate (ipr) ~0.0012 higher than the center line as shown in the Table 1. The
~0.0031 cutting edge of all the PSG-S type Micro-Bars is designed to
Carbon Steel - Wet be higher than the center line. (L4 of Micro-Bars dimension)
Alloy Steel
Stainless Steel 100~330 - : 1st Recommendation
~980
100~260
-
F MM / FNM
Recommended Insert Grade (Vc sfm) Face Grooving (FMM / FMN ) Traversing (FMM)
Workpiece Cermet CVD PVD Carbide Edge Width (in) Edge Width (in) Notes
Material
0.1181 0.1575 0.1969 / 0.2362 0.1181 0.1575 0.1969 / 0.2362
TN90 CR9025 PR915 PR930 PR905 KW10
Feed Rate (ipr) Feed Rate (ipr)
Carbon Steel - - 0.0012~0.0020 0.0012~0.0031 0.0020~0.0039 0.0020~0.0039 0.0020~0.0098 0.0039~0.0118
330~720 260~660 260~660 260~660
Alloy Steel - - 0.0012~0.0020 0.0012~0.0031 0.0020~0.0039 0.0020~0.0039 0.0020~0.0098 0.0039~0.0118
260~660 230~590 230~590 230~590
Stainless Steel - - 0.0012~0.0020 0.0012~0.0031 0.0020~0.0039 0.0020~0.0039 0.0020~0.0098 0.0039~0.0118
0.0020~0.0039 0.0020~0.0039 0.0020~0.0098 Wet
230~520 200~490 200~490 200~490
0.0039~0.0118
Cast Iron - - - - 0.0012~0.0020 0.0012~0.0031
260~590 230~490
Aluminum - - - - - 0.0012~0.0020 0.0012~0.0031 0.0020~0.0039 0.0020~0.0039 0.0020~0.0098 0.0039~0.0118
660~1640
Brass - - - - - 0.0012~0.0020 0.0012~0.0031 0.0020~0.0039 0.0020~0.0039 0.0020~0.0098 0.0039~0.0118
: 1st Recommendation : 2nd Recommendation
330~660
• Set the feed rate 1/100 of edge width on the first groove and check chip evacuation.
• FMN type Inserts are only for Deep Grooving, and when used for turning, set to D.O.C. = 0.079" and under.
Turning Conditions
FMM Toolholder
Recommended Cutting Conditions
D.O.C. (MAX) (in) Under 50% of Edge Width D.O.C. 0.0197w
f (MAX) (ipr) Under 3~5% of Edge Width f [0.0012(Min.) ~ 0.0020(Max.)] w
• (D.O.C.) x ( f ) should be as follows.
Edge Width (in) 0.1181 0.1575 0.1969 0.2362
Load (in2)
D.O.C. x Feed Rate (f) ~0.004 ~0.006 ~0.010 ~0.014 • D.O.C. x f 0.0004w2
kyocera@kyocera-tools.ru
G126 www.kyocera-tools.ru