для заказа - kyocera@kyocera-tools.ru Integral Type
FACE GROOVING TOOLHOLDERS (ROUND SHANK) [GVF INSERT] 'BDF(SPPWJOH%JB%
GIFV 5PPVUFSEJB
5
"
'
%
'BDF(SPPWJOH%JB% - )
-
5PPVUFSEJB
(*'73#" (*'7-#"
4IPXT3JHIU'JHVSF 4IPXT-FGU'JHVSF
• Right-hand shown • Left-hand shown
• Right-hand Insert for Right-hand Toolholder, Left-hand Insert for Left-hand Toolholder.
T oolholder Dimensions
Stock Dimensions (mm) Face Grooving Spare Parts
Dia. D
Clamp Set Wrench Applicable Inserts
T MIN MAX
Part Number G116
R L A D H L1 L2 F
GIFV§ 3532B-201A 35 32 30 250 23 16 2.2 35 CPS-5V - FT-15 - GVF§...-...A
(12) - CPS-6V - LW-3 GVF§...-...AR
50 - CPS-8V - LW-4 GVF§250~350-020B
GIFV§ 3532B-351B 35 32 30 250 30 16 4.6 35 () GVF§300-150BR
(25) GVF§400~490-020B
50 GVF§400-200BR
3532B-352B 35 32 30 250 30 16 5.1 35 () GVF§250~350-020B
(25) GVF§300-150BR
70 GVF§400~490-020B
5032B-501B 50 32 30 250 30 16 4.6 50 () GVF§400-200BR
(25)
70 GVF§350~450-040C
GROOVING 5032B-502B 50 32 30 250 30 16 5.1 50 ()
(25) GVF§500~600-040C
G 70
GIFV§ 5032B-501C 50 32 30 250 35 16 6.6 50 ()
EXTERNAL (25)
INTERNAL 70
5032B-502C 50 32 30 250 35 16 8.1 50 ()
(25)
Note 1. Dimension T shows available grooving depth.
2. Standard toolholders are designed with the edge position 1.0mm above the center.
FACE F ace Grooving Dia. D1 depends on the application.
Applications Part Number Face Grooving Face Grooving Notes
Dia. Dia.
d1 (mm) D (mm)
(MIN) MIN MAX (MAX)
GIFV§ 3532B-201A
GIFV§ 3532B-351B 35
3532B-352B 50
E E % 5032B-501B - -
5032B-502B 50 70
GIFV§ 5032B-501C
5032B-502C
GIFV§ 3532B-201A 12 If D2 58-2W, the Face Grooving Dia.
GIFV§ 3532B-351B 35 can be expanded to d1 (MIN.) toward
3532B-352B 50 the Center.
W = Edge Width
% 5032B-501B
% 25
5032B-502B 50 70 If D2 75-2W, the Face Grooving Dia.
can be expanded to d1 (MIN.) toward
GIFV§ 5032B-501C the Center.
5032B-502C W = Edge Width
GIFV§ 3532B-201A 12
GIFV§ 3532B-351B 35
3532B-352B 50
E % 5032B-501B 25 -
5032B-502B 50 70
GIFV§ 5032B-501C
5032B-502C
• The value ( ) of Face Grooving Dia. (D1 MAX.) is the maximum outer diameter value after the initial groove between MIN.~MAX. (It is possible to widen the groove to infinity )
• The value ( ) of Face Grooving Dia. (d1 MIN.) is the minimum diameter of the boss which remains in the center when widening the groove width to a smaller value after the initial groove between
MIN.~MAX.
G122 kyocera@kyocera-tools.ru U.S. Stock Standard :
www.kyocera-tools.ru World Express (Shipping: 7-10 Business Days) :