для заказа - kyocera@kyocera-tools.ru
SIGE INTERNAL GROOVING
SIGE-EH Excellent Bar (With Coolant Hole) Coolant Hole (d) 2° Coolant Hole (d)
L2 Fig.2
2° D GRADES
A
A Fig.1 D A
F F D B
T T H C
L1 D
A L2 H E
2° L1 F
G
Coolant Hole (d) Coolant Hole (d) INSERTS H
J
F D Fig.3 Fig.4 N
T H P
L2 H Coolant Hole (d) R
A 2° L1 Fig.5 1612C-EH shank is 3 face cut type CBN & PCD T
(top, bottom and one side)
H
F L1 D
T
L2 TOOLHOLDERS SMALL TOOLS
A 2° Coolant Hole (d)
D Fig.6
F
T
H
L2 L1
• Right-hand shown Right-hand Insert for Right-hand Toolholder, Left-hand Insert for Left-hand Toolholder
T oolholder Dimensions BORING
Stock Min. Spare Parts
Bore Dimensions Clamp Screw Wrench
Unit Dia. Drawing Applicable Inserts
Part Number FT
G52~G54
RL A D H L1 L2 F T d DT
GROOVING
SIGE§ 05EH 0.313 0.315 0.283 3.940 0.787 0.177 0.059 0.158 Fig.1 SB-2045TRN FT-6 - GE§100-005A~GE§200-010A
GER100-050AR~GER200-100AR
06EH 0.394 0.394 0.354 4.920 0.984 0.232 0.087 0.158 Fig.1 SB-2255TR - DT-7 GE§100-005B~GE§300-020B
GER100-050BR~GER200-100BR
0809C-EH 0.551 0.500 0.460 5.900 1.300 0.315 0.098 0.158 Fig.2 SB-2570TR FT-8 GE§100-005C~GE§350-020C CUT-OFF
0810C-EH - GER150-010CM~GER350-020CM
inch 0.630 0.500 0.460 5.900 0.788 0.335 0.098 0.158 Fig.3
1213D-EH GER200-100CR~GER300-150CR
1616E-EH GE§100-005D~GE§400-020D
2020E-EH 0.790 0.750 0.710 7.09 1.575 0.477 0.177 0.196 Fig.5 SB-3080TR FT-10 - GER150-010DM~GER400-020DM
2025E-EH
GER200-100DR~GER300-150DR
1.000 1.000 0.960 7.88 1.772 0.614 0.255 0.196 THREADING
Fig.5
1.250 1.250 1.170 8.66 2.166 0.748 0.255 0.196 SB-4085TR FT-15 - GE§100-005E~GE§500-020E
GER150-010EM~GER500-020EM
1.575 1.250 1.170 9.84 1.772 0.906 0.255 0.196 Fig.6
SIGE§ 0808A-EH 8 8 7.2 100 20 4.8 1.5 3 Fig.1 SB-2045TRN FT-6 - GE§100-005A~GE§200-010A
- DT-7 GER100-050AR~GER200-100AR
1010B-EH 10 10 9.0 125 25 6.2 2.2 3 Fig.1 SB-2255TR GE§100-005B~GE§300-020B HSK TOOLING SPARE PARTS
1210B-EH 12 10 9.0 125 30 7.0 2.2 3 Fig.2 SB-2570TR GER100-050BR~GER200-100BR
1412C-EH 14 12 11.4 150 33 8.0 2.5 4 Fig.3
1612C-EH mm 16 12 11.4 150 20 8.5 2.5 FT-8 GE§100-005C~GE§350-020C
1616C-EH 16 16 15.0 160 36 9.0 2.5 4 Fig.4 - GER150-010CM~GER350-020CM
2020D-EH 20 19.0 180 40 12.1 4.5 5 Fig.5 GER200-100CR~GER300-150CR
2525E-EH 20 25 24.0 200 45 15.6 6.5 5 Fig.5 SB-3080TR GE§100-005D~GE§400-020D
3232E-EH 32 30.4 220 55 19.0 6.5 FT-10 - GER150-010DM~GER400-020DM
4032E-EH 32 30.4 250 45 23.0 6.5
GER200-100DR~GER300-150DR
25 5 Fig.5 SB-4085TR FT-15 - GE§100-005E~GE§500-020E
32 5 GER150-010EM~GER500-020EM
40
5 Fig.6 TECHNICAL
• Dimension T shows available grooving depth. Available Groove Depth : “B” Dimension of Insert.
Features
Traditional top clamp has been replaced with a screw C utting Edge is Protected in the Pocket
clamp only. This design creates a large chip pocket
that provides excellent chip evacuation Contact Face INDEX
Large Chip Pocket Contact Face
Screw Clamp 8 mm Minimum Cutting Diameter with 2-Edge Design
Conventional Clamp
Cost effective chip control from a 3-D molded chipbreaker
GER···M type
: U.S. Stock Standard kyocera@kyocera-tools.ru G55
: World Express (Shipping: 7-10 Business Days) www.kyocera-tools.ru