Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

                                                                    для заказа - kyocera@kyocera-tools.ru

GUIDE FOR EXTERNAL GROOVING

 Guide for External Machining                                                                                                                                                                                            GRADES                   A
                                                                                                                                                                                                                                                   B
     (Turning After Grooving)                                                                             Before traversing, pull the tool back about 0.004"                                                             INSERTS                  C
                                                                                                                                 after grooving.                                                                                                   D
        1. Grooving Depths Over 0.020" : At Roughing (Fig.1)                                                                                                                                                              CBN & PCD                E
        	 Before traversing, pull the tool back about 0.004" after grooving,                                   (Grooving depth over 0.020" : At roughing)                                                                                          F
                                                                                                                                    Fig.1
            instead of traversing subsequent to grooving.
        	 (Failure to pull the tool back before traverse cutting will result in an

            unbalanced load applied on only one side of the cutting edge.)

        2. Grooving Depths Under 0.020" : At Finishing (Fig.2)
        	 Traversing subsequent to grooving is possible because shallow

            groove depths relate a small load on the cutting edge.
        	 (Dwell-motion is not necessary)

                                                                                                                           Traversing subsequent to grooving.                                                            TOOLHOLDERS SMALL TOOLS
                                                                                                                       (Grooving depth under 0.020" : At Finishing)
   1. When widening the groove width, apply the "Step Turning" as shown in Fig.3
                                                                                                                                            Fig.2
   2. The widened groove and side walls should be finished last.
       (For better chip control, D.O.C. over 0.020" is recommended.)

   Note: If the workpiece is not supported at the center, reduce the feed rate
   when grooving towards center

                                                                                                                                                                                                                          BORING

                                                                                                                                   0.004”                                                                                 GROOVING                 G
                                                                                                                                                                                                                                                   H
                                                                                                                                     Fig.3                                                                                CUT-OFF                  J
                                                                                                                                                                                                                                                   N
 Case Studies                                                                                                                                                                                                                                     P
                                                                                                                                                                                                                                                   R
                              5120H (Grooving)                                                 Structural Steel (Grooving Turning)                                                                                        THREADING                T

• Gear                         0.394”                                                  • Gear                                                                                                                             HSK TOOLING SPARE PARTS
• Vc = 370~540 sfm                                                                     • Vc = 560 sfm
• f = 0.002 ipr               321 4                                                    • f = 0.006 ipr (Roughing)
• Wet
• GDM4020N-040GM                                                                             0.004 ipr (Finishing)
                                                                                       • D.O.C = 0.008"
                    (PR1225)                                                           (Finishing)
• KGDL2525X-3T10S                                                                      • Wet
                                                                                       • GDM4020N-040GM

                                                                                                           (PR1215)
                                                                                       • KGDR2525X-4T20S
                                                                 24
                                                                            35
                                                                                                                                                             73

                                                                                                                                                                                                               38
                                                                                                                                                                                                                     54

GM Chipbreaker                           1,500 pcs/C                                   GM Chipbreaker                              250 pcs/C                                                                              TECHNICAL
     (PR1225)                                                                               (PR1215)
                                                           6X Longer Life
 Competitor K                                                                               Competitor L                           200 pcs/C
                              250 pcs/C
 (PVD Coated Carbide)                                                                  (Roughing: PVD Coated Carbide)
                                                                                                (Finishing: Cermet)

• KGD type grooving toolholder + GM chipbreaker (PR1225) showed                        • GM chipbreaker reduced occurrence rate of tangle of chips (occurrence rate                                                       INDEX
  6 times longer tool life than that of Competitor K.                                    80%  10%). The problem was persistent with Competitor L.Machining
                                                                                         productivity is improved.
• Good chip control without burned chips.

                              Competitor K                       GM Chipbreaker        Chips easily tangled Competitor L           Smooth chip control  GM Chipbreaker
                                                                    (User Evaluation)                                 (Finishing)                           (Finishing)

                                                                                                                                                             (User Evaluation)

                                                                 kyocera@kyocera-tools.ru                                                                                                                                 G29
                                                                    www.kyocera-tools.ru
Заявка