Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

Kyocera - Каталог Токарный инструмент 2016 ENG

                                                                    для заказа - kyocera@kyocera-tools.ru

INTERNAL SPHERICAL MACHINING, INTERNAL FACING, COPYING

 A...SVJP(C)-, S...SVJP(C)- Excellent Bar (Internal Spherical Machining / Internal Facing)                                                                                                                AGRADES
                                                                                                                                                                                                             B
    Refer to Page  F58 (Dynamic Bar)                                                                                                                                                                      C
                                                                                                                                                                                                             D
 1. Application Range                                                                                                                                                                                        E
                                                                                                                                                                                                             F
                                  547+#e                                                                                                                                                           GINSERTS
                                       447+#e                                                                                                                                                      H
                                                                                                                                                                                                             J
                                                    447+#e                                                                                                                                         N
                                                             347+#e                                                                                                                                P
                                                                                                                                                                                                             R
                                                     247+$                               3	"
    "                                                                                      T
                                                                 .47+$e                           -             D.O.C.
                                                                    .47+1e                                                                                                                  F59
                     7#                                                                                                       -                                                                      CBN & PCD
                     UZQF       7#              
                                       UZQF

                                                         7$	1

                                                         UZQF

2. Machining Method                                                                                                                                                                                           TOOLHOLDERS SMALL TOOLS

                                   In Cases with No Existing Hole                           d = 0.020”                                              Finishing
                                                                                      (When Corner R (r) = 0.016”)                       Spherical Machining
                                    d = 0.020”
                              (When Corner R (r) = 0.016”)

Spherical Machining                                      Internal Facing

                                                                                                                                                                                                              BORING

                                      f = 0.002 ipr                                                                                                                                                           GROOVING

                     (Note) f should be under 0.002 ipr at internal facing                                                                    Internal Facing
                                     In Cases with Drilled Hole
                                                                                                                                                  
                                               Spherical Machining                                                                                                                                 

                                                                                                                                      Machining Process                                                       CUT-OFF
                                                                                                                                         1. Finish the internal face firstly.
                                                    Internal Facing                                                                      2. Next, finish the internal diameter.                               THREADING

                     Drilled Hole

                                        f = 0.002 ipr                                                                                                                                                         HSK TOOLING SPARE PARTS

                     (Note) f should be under 0.002 ipr during internal facing

3. Caution

                                                                                                                                      16 Spherical Machining

                                                         When machining past the center of the workpiece,                             R8
                                                         insert breakage may occur.                                                                    R7.6
                                                                                                                                                      (When Corner-R (r) is 0.4)
                                                                                                                                                                                                              TECHNICAL
                                                                                                      Set the insert edge at the
                                                                                                      center of the workpiece.                                                                        INDEX

                                                                                                                                           Adjust the machining program of radius
                                                                                                                                           smaller by Corner-R (r) value.
                                                                                      For internal profiling, D.O.C. should be
                                                                                      less than the value of Corner-R (r).

                                                        Machining of this kind is available,                                         Less than Corner-R (r)
                                                         but the oblique part may be scratched by chips.

                                                                                                                     [Burrs may occur, if D.O.C. is bigger than Corner-R (r)]

                                  Poor finish

                                                                               kyocera@kyocera-tools.ru
                                                                                  www.kyocera-tools.ru
Заявка