Kyocera - Каталог Токарный инструмент 2016 ENG
для заказа - kyocera@kyocera-tools.ru
INSERT IDENTIFICATION SYSTEM
Symbol Insert Symbol Hole Hole Shape Chipbreaker Insert
H Hexagon N No -
O Octagon
P Pentagon Tolerance R No - One Side
S Square Thickness
T Triangle Symbol Corner Height I.C. Size F Two Sides
C 80 Diamond (Class)
D 55 Diamond ANSI ISO ANSI ISO ANSI ISO A No
E 75° Diamond (±inch) (±mm) (±inch) (±mm)
F 50° Diamond Symbol Relief Angle (±inch) (±mm) M With Hole One Side
M 86° Diamond
J 70 Diamond A 3 A 0.0002 0.005 0.0010 0.025 0.0010 0.025
V 35 Diamond B 5 F 0.0010 0.025 0.0005 0.013
W 80 Trigon C 7 C 0.0002 0.005 0.0010 0.025 0.0010 0.025 G Two Sides
L Rectangle D 15 H 0.0010 0.025 0.0005 0.013
A 85° Parallelogram E 20 E 0.0005 0.013 0.0010 0.025 0.0010 0.025 W With Hole and No
B 82° Parallelogram F 25 G 0.0050 0.130 0.0010 0.025
K 55° Parallelogram G 30 J 0.0005 0.013 0.0010 0.025 0.002~0.006 0.05~0.15 One Countersink
R Round N 0 0.0010 0.025 0.002~0.006 0.05~0.15
P 11 K 0.0010 0.025 0.0010 0.025 0.002~0.006 0.05~0.15 T 40~60 One Side
L 0.0050 0.130 0.002~0.006 0.05~0.15
M 0.0010 0.025 0.0010 0.025 0.002~0.006 0.05~0.15 Q Yes With Hole and No
N 0.0050 0.130 0.003~0.009 0.08~0.25
U 0.0002 0.005 Two Countersink
0.0005 0.013 U 40~60 Two Sides
0.0010 0.025 B With Hole and No
0.003~0.007 0.080~0.180 One Countersink
0.003~0.007 0.080~0.180 H 70~90 One Side
0.005~0.015 0.130~0.380 C With Hole and No
Shown angle stands for Insert's periphery is as fired. J Two Countersink
acute angle for rhombic Tolerance difference depends on size and shape of insert 70~90
and parallelogram inserts. Two Sides
X- - -
Shape Symbol Relief Angle Symbol Tolerance Symbol Hole / Chipbreaker Symbol
ISO C N M G 12 04 08 PG
(metric)
ANSI C N M G 4 3 2 PG
(inch)
Edge Length Symbol (ISO) I.C. Size (ANSI) Thickness Symbol Corner-R(r) Symbol Manufacturer's
I.C. Size Option
ISO ANSI ISO ANSI
Hand Symbol,
C D S R T VW (mm) I.C. Size Symbol Thickness Symbol Thickness Symbol Corner-R(r) Symbol Corner-R(r) Symbol Chipbreaker,
(inch) (mm) (inch) (mm) (inch) Symbol, Etc.
03 04 03 06 3.97 5/32 1.2 1.59 01 1/16 1 Sharp Corner 00 0.000 00
4.76 3/16 1.5 1.98 T1 5/64 1.2 0.03 003 0.001 0.1
04 05 04 08 08 2.38 02 3/32 1.5 0.05 005 0.002 0.13
5 7/32 1.8 2.78 T2 0.10 01 0.004 0.2
05 5.56 3.18 03 - - 0.20 02 0.008 0.5
1/4 2 3.97 T3 1/8 2 0.40 04 1/64 1
05 06 05 09 03 6 5/16 2.5 4.76 04 5/32 2.5 0.80 08 1/32 2
6.35 5.56 05 3/16 3 1.20 12 3/64 3
06 7.94 3/8 3 6.35 06 7/32 3.5 1.60 16 1/16 4
7.94 07 1/4 4 2.00 20 5/64 5
06 07 06 11 11 04 8 1/2 4 9.525 09 5/16 5 2.40 24 3/32 6
9.525 5/8 5 3/8 6 2.80 28 7/64 7
08 09 07 13 05 3.20 32 8
10 3/4 6 00 1/8
08 12 Round (inch)
12.7 7/8 7 insert or MO Round
09 11 09 09 16 16 06 15.875 (metric) insert
16 1 8
12 10 19.05 1-1/4 10
20
12 22.225
25
12 15 12 12 22 22 08 25.4
31.75
16 19 15 15 27 27 10 32 T
16
19 23 19 19 33 33 13
20 T
22 27 22 38
25 Thickness displayed as the distance between
bottom surface and highest point on cutting edge.
25 31 25 25 44 44 17
32 38 31 31 54 54 21
32
• Expressed as edge length for ISO. When a minus tolerance is specified for the corner-R(r)
• ANSI expresses the inscribed circle diameter in inches.
• If a minus tolerance is specified for the corner-R(r) as shown in the Fig.1, using
Positive Insert Identification System an insert with corner-R(r) = 0.008" may result in larger radius than specified.
(e.g. of (8) Manufacturer's Option) • Use an insert the corner of which R(r) has a minus tolerance.
CCGT21502M E R - U CCGT21502M F P - GF
Corner-R(r) for Corner-R(r) for
Minus Tolerance Minus Tolerance
Honed Edge Chipbreakers Sharp edge Chipbreakers R0.008” or less
Insert Hand Mirror-Finish
Fig.1 Example of a specified corner-R in the drawing
Inserts
B2 kyocera@kyocera-tools.ru
www.kyocera-tools.ru