Kyocera - Каталог Токарный инструмент 2016 ENG
для заказа - kyocera@kyocera-tools.ru Wedge Lock
EXTERNAL TOOLHOLDERS [TN INSERT] Side Rake Angle: -6°
Angle of Inclination: -6°
W TJN (External / Copying) WTJN§2020K type:
Shim Nut sticks out
' m - - ) # as shown below.
I '
m Side Rake Angle: -6°
• Right-hand shown m Angle of Inclination: -6°
WTKN§2020K type:
WTKN (External / Facing / Copying)TOOLHOLDERS ' - m ) # Shim Nut sticks out as
I ' - shown below.
D m
Back Rake Angle: -8.5°
m WTENN2020K type:
• Right-hand shown
Shim Nut sticks out as
W TEN (External / Chamfering) shown below.
m
- -
I ' ) #
m Standard
Corner-R(r)
Toolholder Dimensions • Right-hand shown
Stock Dimensions Clamp Set Shim Spare Parts Wrench Spacer
Shim Pin Shim Nut
Part Number Unit
RNL H1=h B L1 L2 F1 F2
WTJN§ 12-3C 0.75 0.75 5.00 1.26 1.00 0.96 WCS-1N WTN-33 WP-1S WN-1 LW-3 WSP-1
16-3D Inch 1.00 6.00 1.26 1.25 1/32 *WTN-33-20
1.00 0.94
WTJN§ 2020K-16N 20 20 125 32 25.0 24 WCS-1N WTN-33 WP-1S WN-1 LW-3 WSP-1
2525M-16N mm 25 0.8 WCS-1N *WTN-33-20 WP-1S WN-1 LW-3 WSP-1
WCS-1N WP-1S WN-1 LW-3 WSP-1
WTKN§ 12-3C 25 150 32 32.0 24 WTN-33
WTKN§ 2020K-16N *WTN-33-20
Inch 0.75 0.75 5.00 1.26 1.00 - 1/32
2525M-16N WTN-33
20 20 125 32 25.0 - *WTN-33-20
mm 25 0.8
25 150 32 32.0 30
WTENN 2020K-16N 20 20 125 32 10.0 - 0.8 WCS-1N WTN-33 WP-1S WN-1 LW-3 WSP-1
2525M-16N mm 25 150 32 12.5 - *WTN-33-20
25
* When using inserts whose corner-R (r) is greater than 1/16", please purchase a shim (WTN-33-20) with * mark and use it in order to prevent workpiece and shim from interfering with each other.
• In wedge lock, use of ceramic insert other than silicon nitride insert is not recommended due to strong restrain force.
A pplicable Inserts
Toolholder Insert Toolholder Insert
WTJN§...12-3C TNA
TNG 33..
WTJN§...16-3D WTENN...-16N TNM
WTJN§...-16N TNA 33..
WTKN§...12-3C TNG
TNM
WTKN§...16-3D
WTKN§...-16N
D16 kyocera@kyocera-tools.ru U.S. Stock Standard :
www.kyocera-tools.ru World Express (Shipping: 7-10 Business Days) :