Kyocera - Каталог Токарный инструмент 2016 ENG
ITEMNSE!W для заказа - kyocera@kyocera-tools.ru
PCD TOOLS How to read this page B13
Grooving
1-Edge
Edge Prep. N Non-Ferrous Metals (with Interruption)
Non-Ferrous Metals (without Interruption)
CBN All PCD Items Sharp Edge S Titanium Alloys (with Interruption)
PCD Titanium Alloys (without Interruption)
PCD
Dimensions (mm) Angle
(°)
POSITIVE Insert ANSI +0.00 No. of Edges
KPD001
Part Number W(±in0.0)012 W(m±m0.0)3 B r-0.05 T H h1 d S Toolholder
TKF12§ 200-AS Page
0.1 3 8.7 7.3 5 5.5
Turning B d 250-AS 0.079 2.0 5.0
Grooving r 8.7 7.3 5 5.5
±0.0012”W TH T 0° 1
r S
0.098 2.5 5.0 0.1 3
±0.0012”W h1 TKF16§ 250-AS 0.098 2.5 8.0 0.1 4 9.5 8.0 5 6.5 0° 1
r TKF12§ 200-ASR
r
250-ASR
Turning 0.079 2.0 5.0 0.1 3 8.7 7.3 5 5.5
Grooving
NEW S d 0° 1
B
0.098 2.5 5.0 0.1 3 8.7 7.3 5 5.5 E12
h1 H
Left-hand insert shown with TKF16§ 250-ASR 0.098 2.5 8.0 0.1 4 9.5 8.0 5 6.5 0° 1
right-hand PCD edge TKF12§ 150-NB
SOLID
GROOVING External Grooving B d 200-NB 0.059 1.5 3.5 0.1 3 8.7 8.3 5 2.0
(Turning is Possible) r 250-NB
±0.0012”W r S HT 0.079 2.0 4.0 0.1 3 8.7 8.3 5 3.0
0° 1
0.098 2.5 4.0 0.1 3 8.7 8.3 5 3.0
h1
250-NB4.5 0.098 2.5 5.0 0.1 3 8.7 8.3 5 4.5
• Lead angle (front cutting edge angle: ) shows the angle when installed into toolholder
• TKF PCD inserts are only for turning and grooving
• Cut-off is not recommended.
• Dimension B shows available grooving depth
Insert Identification System Applicable Range
TKF 12 R 200 - AS R TKF12-AS/-ASR TKF16-AS/-ASR
TKF 12 L 200 - AS
Insert Type Insert Size Width PCD Insert Hand D.O.C. (in) 0.24 D.O.C. (in) 0.24
(Edge Width) 0.20 0.20
Without Indication: 0.16 0.16
Insert Hand Name of Chipbreaker The edge hand is the same 0.12 0.12
R : Right-hand AS : AS Chipbreaker 0.08 0.08
L : Left-hand NB : Without Chipbreaker as the insert hand. 0.04 0.04
R : Right-hand
0.004 0.008 0.004 0.008
f (ipr) f (ipr)
• TKF PCD inserts are only for turning and grooving
• Cut-off is not recommended
KTKF Toolholder
Note) 1. The cutting edge of the TKF-AS/-ASR will be 0.04" lower than the center h1 H1 H1
line when attached to the KTKF toolholder (Ref. Fig.1). Adjust the height Fig.1 When a TKF-AS/-ASR insert is attached
by making NC lathe parameter settings or inserting a plate. (The cutting edge is 0.04” lower than the center line.)
2. If the 0.04" adjustment is not possible on your automatic lathe, use the KTKF Toolholder
TKF-NB (Ref. Fig.2).
h
Fig.2 When a TKF-NB insert is attached
kyocera@kyocera-tools.ru
C32 CBN & PCD Inserts www.kyocera-tools.ru : U.S. Stock : U.S. Stock (R-hand Only) : U.S. Stock (L-hand Only)
sold in 1 piece boxes.
: World Express (Shipping: 7-10 Business Days) : World Express (R-hand Only) : World Express (L-hand Only)