Kyocera - Каталог фрезерование 2017 ENG
для заказа - kyocera@kyocera-tools.ru
MSTA SLOT MILL (SELF-CLAMPING)
Set up
8SFODI4VQQPSU)PMF )PXUPJOTUBMMJOTFSUT GRADES A
B
*/*OEJDBUFE4JEF 1VUJOTFSUJOTJEFUIFTMPUNJMM C
*OTFSUPOFPGUIFQJOTPOUIFXSFODI PO*/JOEJDBUFE D
065 */ LINEUP / INSERTS 45 / 70 LEAD E
TJEF
JOUPUIFXSFODITVQQPSUIPMF F
6TJOHUIFPUIFSQJO
QVTIUIFGSPOUSFMJFGTVSGBDFPGUIF G
H
JOTFSU J
3PUBUFUIFXSFODIVOUJMJOTFSUTCBDLFOENBLFT K
O
DPOUBDUXJUITMPUNJMM P
)PXUPSFNPWFJOTFSUT
065*OEJDBUFE4JEF *OTFSUPOFPGUIFQJOTPOUIFXSFODI PO065JOEJDBUFE 75 LEAD
TJEF
JOUPUIFXSFODITVQQPSUIPMF
BOEJOTFSUPUIFSQJO
*OTFSU3FNPWBM)PMFGPS8SFODI JOUPUIFJOTFSUSFNPWBMIPMF 90 LEAD
*OTFSUDBOCFSFNPWFECZSPUBUJOHUIFXSFODIDPVOUFS
DMPDLXJTF "NBHOFUJTJOTUBMMFEPO065JOEJDBUFE
TJEF
Note) Use appropriate wrench for set up. HIGH FEED
Recommended Cutting Conditions
Recommended Insert Grade (Vc: sfm) fz (ipt)
Workpiece Hardness CVD PVD Edge Width Notes
Material (HRC) Coated Carbide Coated Carbide
MULTI-FUNCTION SLOT MILLS RADIUS / BALL-NOSE OTHER APPLICATIONS TOOL HOLDING SPARE PARTS
CA0835 PR0735 0.063" 0.087" (0.089") 0.118" 0.157"
1.60mm 2.20mm (2.25mm) 3.00mm 4.00mm
0.001~0.005 0.003~0.008
Low Carbon Steel 1010~1025 20 820~1020 660~820 0.002~0.006 0.002~0.007
Carbon Steel 1030~1059, 1060 29
37 520~620 430~520 0.001~0.005 0.002~0.006 0.002~0.007 0.003~0.008
Alloy Steel Annealed 28
High Carbon Alloy 1030~1059, 1060 41 460~590 360~490 0.001~0.005 0.002~0.006 0.002~0.007 0.003~0.008
Stainless Steel 42
Gray Cast Iron Heat Treated 33 460~590 360~490 0.001~0.005 0.002~0.006 0.002~0.007 0.003~0.008 Coolant
Nodular Cast Iron Annealed 45
38 390~520 330~430 0.001~0.004 0.002~0.005 0.002~0.006 0.003~0.007
Heat Treated 25
37 330~460 260~390 0.001~0.004 0.002~0.005 0.002~0.006 0.003~0.007
D2, H13, etc.
304, 316, etc. 490~620 260~390 0.001~0.004 0.002~0.005 0.002~0.006 0.003~0.007
Austenitic 460~590 200~260 0.001~0.004 0.002~0.005 0.002~0.006 0.003~0.007
403, 410, etc.
520~660 - 0.001~0.005 0.002~0.006 0.002~0.007 0.003~0.008
Martensitic
NO.45~NO.60 430~520 - 0.001~0.005 0.002~0.006 0.002~0.007 0.003~0.008 Dry
60-40-18~70-50-05 360~460 - 0.001~0.005 0.002~0.006 0.002~0.007 0.003~0.008
80-60-03~120-90-02
Note) 1. Use down-cut machining. %0$
2. If D.O.C. is under 1/10 of Cutter Dia.(D), it is possible
to increase feed per tooth (fz) 40%. %
TECHNICAL R
INDEX T
kyocera@kyocera-tools.ru H7
www.kyocera-tools.ru