Kyocera - Каталог фрезерование 2017 ENG
для заказа - kyocera@kyocera-tools.ru
MSRS90
Caution when Installing Notched Inserts When installing the inserts, match the number on the top of insert to the number of the cutter body.
It is important to install the appropriate notched insert into the correct position. Failure to Same Number
do so may result in damage to the toolholder body. The appropriate insert is marked on
the pocket of the cutter body.
No. of Inserts Same Number
Description No. of No. of No. of Notched
Inserts Flutes Stages
MSRS 90100R-1-6T NB3(P) NB4(P)
90100R-2-6T 6 6 1
90100R-4-6T 12 2 33
24 4
66
12 12
Spare Parts (Inch and Metric Toolholders)
Spare Parts
Clamp Screw Wrench Cartridge Clamp Screw Wrench Anti-Seize Arbor Bolt
Compound
Part Number MAP-1806M MAP-1806S
MP-1
(Bottom Edge Only)
MSRS 903000R-1-4T
90 LEAD 903000R-2-4T HH1/2-1.25
Without
Cartridge
E 903000R-4-4T - - - -
MSRS 904000R-1-6T
SB-60120TR TT-25L
904000R-2-6T Recommended Torque for MP-1
MSRS 905000R-1-8T Insert Clamp 7.5 N·m
-
MSRS 906000R-1-8T
With Without With Without With 908000R-1-10T MAP-1806M - SB-40140TR DT-15
Cartridge Cartridge Cartridge Cartridge Cartridge 9010000R-1-12T
Recommended Torque for Cartridge Clamp 3.5 N·m
MSRS 90080R--4T HH16X45
HH20X55
90100R--6T ----
-
90125R--8T HH12X35
MSRS 90160R--8T MAP-1806M*1 MAP-1806S*2 SB-40140TR DT-15 -
90315R--14T ~~ SB-60120TR TT-25L Recommended Torque for Cartridge Clamp 3.5 N·m
MSRS 90080R--4T-M
Recommended Torque for MP-1
90100R--6T-M Insert Clamp 7.5 N·m
90125R--8T-M --- -
MSRS 90160R--8T-M DT-15
MAP-1806M*1 MAP-1806S*2 SB-40140TR
90315R--14T-M Recommended Torque for Cartridge Clamp 3.5 N·m
*1: MAP-1806M is only for applicable MSRS90...R-1... cutters
*2: MAP-1806S is only for the bottom edge (1st stage) of MSRS90...R-2... Use it only for the bottom edge (1st stage).
How to Attach the Cartridge : You need to tighten 2 clamp screws to fix the cartridge. Tighten the slant screw first and then tighten the other screw.
Coat Anti-Seize Compound (MP-1) thinly on portion of taper and thread prior to installation.
Recommended Cutting Conditions
Feed Rate fz (ipt) Recommended Insert Grade (Vc sfm)
Workpiece General Purpose Low Cutting Force MGACOAT
Material NB3+NB4 NB3P+NB4P
PR1230 PR1210
Soft Steel 0.004~0.008~0.010 0.004~0.008~0.010
Carbon Steel 0.004~0.008~0.010 0.004~0.008~0.010
Alloy Steel 0.004~0.006~0.008 0.004~0.006~0.008 400~500~725 400~500~725
Die Steel 0.004~0.006~0.008 0.004~0.005~0.006
Gray Cast Iron 0.004~0.008~0.012 0.004~0.008~0.010
Nodular Cast Iron 0.004~0.008~0.010 0.004~0.007~0.008 325~500~650 325~500~650
325~500~650 325~500~650
325~500~600 325~500~600
325~600~825 325~600~825
325~600~725 325~600~725
Stainless Steel Not Recommended
Non-Ferrous Metals Not Recommended
:1st Recommendation : 2nd Recommendation
E56 kyocera@kyocera-tools.ru
www.kyocera-tools.ru