Kyocera - Инструмент для обработки мелких деталей 2016 ENG
ITEMNSE!W для заказа - kyocera@kyocera-tools.ru
PCD TOOLS
GroovingGRADES
1-Edge N Non-Ferrous Metals (with Interruption)
A Non-Ferrous Metals (without Interruption)
Edge Prep.INSERTSSharp Edge S Titanium Alloys (with Interruption)
Titanium Alloys (without Interruption)
All PCD Items PCD
Dimensions (mm) Angle
B (°)
C InsertCBN & PCD ANSI W(±in0.0)012 W(m±m0.0)3 B +0.00 T H h1 d S No. of Edges
KPD001
E Part Number r-0.05 3 8.7 7.3 5 5.5 Toolholder
Turning TKF12§ 200-AS 8.7 7.3 5 5.5 Page
Grooving 0.1 9.5 8.0 5 6.5
250-AS 0.079 2.0 5.0
TKF16§ 250-AS 0°
TURNING 0.098 2.5 5.0 0.1 3 1
0.098 2.5 8.0 0.1 4 0°
0° 1
F TKF12§ 200-ASRBORING 0.079 2.0 5.0 0.1 3 8.7 7.3 5 5.5 0°
1
250-ASR 0.098 2.5 5.0 0.1 3 8.7 7.3 5 5.5 0° E12
GROOVINGG Left-hand insert shown with TKF16§ 250-ASR 0.098 2.5 8.0 0.1 4 9.5 8.0 5 6.5 0° 1
right-hand PCD edge
External Grooving TKF12§ 150-NB 0.059 1.5 3.5 0.1 3 8.7 8.3 5 2.0 0°
(Turning is Possible) 200-NB
0.079 2.0 4.0 0.1 3 8.7 8.3 5 3.0 0°
CUT-OFFH 250-NB 1
0.098 2.5 4.0 0.1 3 8.7 8.3 5 3.0 0°
250-NB4.5 0.098 2.5 5.0 0.1 3 8.7 8.3 5 4.5 0°
SOLID END MILLS THREADING• Lead angle (front cutting edge angle: ) shows the angle when installed into toolholder
J • TKF PCD inserts are only for turning and grooving
• Cut-off is not recommended.
• Dimension B shows available grooving depth
Insert Identification System Applicable Range
L TKF 12 R 200 - AS
TKF 12 L 200 - AS R
MILLINGM Insert Type Insert Size Width PCD Insert Hand
(Edge Width)
Insert Hand Name of Chipbreaker Without Indication:
SPARE PARTS The edge hand is the same
P R : Right-hand AS : AS Chipbreaker as the insert hand.
L : Left-hand NB : Without Chipbreaker R : Right-hand
TECHNICAL • TKF PCD inserts are only for turning and grooving
R • Cut-off is not recommended
INDEXT Note) 1. The cutting edge of the TKF-AS/-ASR will be 1mm lower than the center
line when attached to the KTKF toolholder (Ref. Fig.1). Adjust the height
by making NC lathe parameter settings or inserting a plete.
2. If the 1mm adjustment is not possible on your automatic lathe, use the
TKF-NB (Ref. Fig.2).
C18 CBN & PCD tools k:yWowocrwledwrEax.k@pryeokssyc(oeScrhaiep-prtaiong-ot:ol7so-.1rl0su.Bruusiness D:aUys.S) .Sto: cWkorld : U.S. Stock (R-hand Only) : U.S. Stock (L-hand Only)
sold in 1 piece boxes. Express (R-hand Only) : World Express (L-hand Only)