Kyocera - Инструмент для обработки мелких деталей 2016 ENG

                                                         для заказа - kyocera@kyocera-tools.ru

CUT-OFF INSERTS

 Edge Prep. and Chipbreakers (CERACUT Plunge & Turn)

   Name          MT Chipbreaker                          TK Chipbreaker                     TMR Chipbreaker                         Without Chipbreaker (NB)          GRADES
    Edge
Preparation      Chamfered + Honed    Chamfered + Honed  Chamfered + Honed    Sharp Edge      Chamfered + Honed                     Honed Cutting Edge  Sharp Edge                               A
                        Corner-R           Sharp Edge           Corner-R        Corner-R             Corner-R                              Corner-R     Sharp Edge                               B
                          0.002"                                                                       0.008"                               0.002"                                               C
                        0.05mm                              0.008"~0.012"    0.008"~0.012"            0.20mm                               0.05mm                                                E
                                                             0.20~0.30mm     0.20~0.30mm                                                                                                         F
                                                                                                                                                                                                 G
                                                                                                                                                                      INSERTS                    H
                                                                                                                                                                                                 J
                 CR9025 / PR915       PR930 / KW10       CR9025 / PR915      PR930 / KW10            PR1115                         CR9025              PR930 / KW10                             L
                                                                                                                                                                                                 M
                                                                             • Sharp Edge can reduce cutting resistance by 40%, compared with chamfered edge          CBN & PCD                  P
                                                                                                                                                                                                 R
   Name                                                                           Advantages                                                                          TURNING                    T
 GMM-MT
 GMM-NB          Specific chipbreaker for cut-off operations requiring sharp cutting performance                                                                      BORING
 GMM-TK          Minimizes the boss
                 Cutting edge is flat with no chipbreaker.
 GMN-TK          Good performance for brass, etc.
GMN (Std.)       Stable design with chipbreaker for cut-off.
                 Large corner-R
                 2-edge for economical performance
                 Same chipbreaker geometry as GMM-TK
                 1-edge.
                 Wide application range.
                 Mainly for deep grooving, but available for groove widening and turning due to projection near side cutting edge.
                 1-edge and wide application range. Available for cut-off applications.

 TMR Chipbreaker                                                             G MM Chipbreaker Map                                                                  GROOVING

 C hipbreaker Advantages

   Special
Curved Wall

                                                                                                                                                                      CUT-OFF

                                      Improved chip evacuation                                                                                                        THREADING SOLID END MILLS
                                          by squeezing chips

             Depression in Center of  Chip Width  Grooving Width
                    Cutting Edge

 T he TMR Chipbreaker Provides Stable Chip Control at High Feed Rates

Good chip control even when cutting speed (spindle revolution) is increased

                                                         (Cutting Conditions : 15CrMo4, 30, Constant Spindle Revolution)

Part Number      n=1060min-1(Vc=325sfm)                                      n=2123min-1(Vc=650sfm)                                                                   MILLING

                 f=0.0008ipr          f=0.0047ipr        f=0.0008ipr                        f=0.0047ipr

   GMM                                                                                                                                                                SPARE PARTS
3020-TMR

 (Neutral)

      GMM                                                                                                                                                             TECHNICAL
3020R-TMR-6D

  (Right-Hand)

 R ecommended Cutting Conditions                                            W orkpiece Surface Roughness

Workpiece        Vc (sfm)             Feed Rate (ipr)                             TMR Chipbreaker provides good surface roughness on the
 Material                                                                         workpiece end face at high feed rate ranges.

Carbon Steel     200~650                                                                                                                                              INDEX

Alloy Steel      200~500              0.003~0.007

Stainless Steel  175~450

                                                         kyocera@kyocera-tools.ru                                                                                     H19
                                                            www.kyocera-tools.ru