Kyocera - Инструмент для обработки мелких деталей 2016 ENG

                                                                                для заказа - kyocera@kyocera-tools.ru

                              PRODUCT LINEUP

                               P roduct Lineup                                                                                                Advantages

                                                Toolholders              KTKF                   (  H8 )                 Insert clamp is side screw type from lateral side
                                                                                                                         2-Edge Insert
A (Long Shank for Automatic Lathe)GRADES                                                                                 Max. Cutting Dia. : 0.630" (16mm)

                                                Cut-Off Diameter                                                         Recommended for very small diameter
                                                                                                                           workpieces, or when clearance between main
                                                0.197"~0.472"                                                            and sub-spindle is very small
                                                ~0.630"
B (5mm~12mm)INSERTS                                                                                                    1-Edge and 2-Edge Inserts Available
                              Small Diameter    (~16mm)                      Width : (0.020"~0.079")                    Max. Cutting Dia. : 0.630" (16mm)
                                                                              Width : (0.5mm~2.0mm)
                                                                                                                         Insert is clamped from top side
                              Cut-Off           Automatic Lathe          KTKFS                  (  H10 )                1-Edge and 2-Edge Inserts Available
                                                                                                                         Max. Cutting Dia. : 1.575" (40mm)
   CBN & PCD                                    For Sub Spindle Tooling
                                                                                                                         Insert is clamped from top side
C Cut-Off Diameter                                                                                                       1-Edge and 2-Edge inserts available
                                                                                                                         Max. Cutting Dia. : 1.575" (40mm)
                                                0.236"~0.472"
                                                0.551"~0.630"                                                          Self-Clamping System
E (6mm~12mm)                                                                                                             Tap the insert lightly with a plastic hammer to
   TURNING                                                                    Width : (0.039"~0.079")                      set it in the pocket.
                                                    (14mm ~16mm)            Width : (1.0mm~2.0mm)
                                                                                                                         1-Edge Insert
                                                                         KGD                    (  H16 )                Max. Cutting Dia. : 2.441" (62mm)

                                                Bolt Clamp

   BORING                     KGD               Cut-Off Diameter

F                                               0.472"~1.575"

                                                (12mm~40mm)

                                                                              Width : (0.079"~0.158")
                                                                              Width : (2.0mm~4.0mm)
   GROOVING
G                                                                        KGM                    (  H20 )
                                                                         KGM-T                  (  H21 )

                                                Bolt Clamp

   CUT-OFF                    CERACUT           Cut-Off Diameter
                              Plunge & Turn
H                              (2-edge Insert)  0.709"~1.575"

                                                (18mm~40mm)

                                                                         Width : 0.059"~0.158",0.118"~0.236"
                                                                         Width : 0.079"~0.197"
   SOLID END MILLS THREADING                                             Width : (1.5mm~4mm, 3mm~6mm)
J Width : (2mm~5mm)
                                                                                                (  H24 )
                                                                                      KTKH-S

                                                Toolholders

L                              CERACUT          Cut-Off Diameter
                                 Cut-Off        1.181"~2.441"

                              (1-edge Insert)

                                                (30mm~62mm)

                                                                              Width : (0.020"~0.079")
                                                                              Width : (0.5mm~2.0mm)

M  C ut-Off in Automatic LatheMILLING

                              1) When a cutting process has just finished

P  SPARE PARTS

R  TECHNICAL

T  INDEX
              2) When returning to the start point

   H2 kyocera@kyocera-tools.ru
                                                                                                  www.kyocera-tools.ru