Kyocera - Инструмент для обработки мелких деталей 2016 ENG

                                                                                      для заказа - kyocera@kyocera-tools.ruGRADES

       SIGE INTERNAL GROOVING

          SIGE-EH Excellent Bar (With Coolant Hole)

A

B  INSERTS

C  CBN & PCD

E  TURNING                                                         Right-hand Shown                                  Right-hand Insert for Right-hand Toolholder, Left-hand Insert for Left-hand Toolholder

                               T oolholder Dimensions

                                                               Stock   Min.                                                               Spare Parts
   BORING                                                              Bore               Dimensions                           Clamp Screw Wrench
F                                                                      Unit Dia.                                     Shape                                                  Applicable Inserts
                              Part Number
                                                                                                                                                                             G38~  G39
                                                               RL      A D H L1 L2 F T d

G SIGE§ 05EHGROOVING                                                 0.313 0.315 0.283 3.940 0.787 0.177 0.059 0.158 Fig.1 SB-2045TRN FT-6            -         GE§100-005A~GE§200-010A
                                                                                                                                                                  GER100-050AR~GER200-100AR

                              06EH                               inch 0.375 0.394 0.354 4.920 0.984 0.232 0.087 0.158 Fig.1    SB-2255TR  -           DT-7      GE§100-005B~GE§300-020B
                                                                                                                                                                  GER100-050BR~GER200-100BR

   CUT-OFF                    0809C-EH                               0.551 0.500 0.460 5.900 1.300 0.315 0.098 0.158 Fig.2                                      GE§100-005C~GE§350-020C

H 0810C-EH                                                                                                                       SB-2570TR  FT-8        - GER150-010CM~GER350-020CM
                                                                                                                                                               GER200-100CR~GER300-150CR
                                                                     0.630 0.500 0.460 5.900 0.788 0.335 0.098 0.158 Fig.3

                              SIGE§ 0808A-EH                         8 8 7.2 100 20 4.8 1.5 3 Fig.1 SB-2045TRN FT-6                                   -         GE§100-005A~GE§200-010A
                                                                                                                                                                  GER100-050AR~GER200-100AR
   SOLID END MILLS THREADING
J 1010B-EH                                                           10         10 9.0 125 25 6.2 2.2              3 Fig.1     SB-2255TR  -           DT-7      GE§100-005B~GE§300-020B
                                                                 mm  12         10 9.0 125 30 7.0 2.2              3 Fig.2                                      GER100-050BR~GER200-100BR
                               1210B-EH

                              1412C-EH                               14 12 11.4 150 33 8.0 2.5 4 Fig.3                                    FT-8               GE§100-005C~GE§350-020C
                              1612C-EH                               16 12 11.4 150 20 8.5 2.5 4 Fig.4 SB-2570TR                                      - GER150-010CM~GER350-020CM

                              1616C-EH                               16 16 15.0 160 36 9.0 2.5 5 Fig.5                                                          GER200-100CR~GER300-150CR

L Dimension T: Available grooving depth

               Traditional top clamp has been replaced with a screw                                                 C utting Edge is Protected in the Pocket
                  clamp only. This design creates a large chip pocket
   MILLING                                                                                                           Contact Face
M that provides excellent chip evacuation
                                                                                                                                            Contact Face
                           Large Chip Pocket

P  8 mm Minimum Cutting Diameter with 2-Edge DesignSPARE PARTS
                              Screw Clamp                                         Conventional Clamp

                               Cost effective chip control from a 3-D molded chipbreaker (GER...M)

R  C hip Evacuation Comparison (Molded Chipbreaker)TECHNICAL                                                                               Chip Evacuation Comparison

                                                                                                                                                (Min. Cutting Dia. 0.315")

                                    Shape                              SCM415 (Min. Bore Dia.)                       Evaluation                            Shape            SCM415   Evaluation
                                                                                                                                                                             0.0008
T ToolholderINDEX                                              0.002"             0.003"              0.004"                                Toolholder

                                   SIGER1612C-EH                                                                     Good Chip Control          SIGER0808A-EH                        Good Chip Con-
                              GER300-020CM (PR1025)                                                                                         GER200-010A (PR1025)                              trol

                              Competitor A                                                            Insert Cracks  Unstable Chip Control
                              (Width 0.118")                                                                                and Biting
                              Competitor B                                                                                                  Competitor C                             Unstable Chip
                              (Width 0.118")                                                                         Unstable Chip Control  (Width 0.079")                               Control
                                                                                                                            and Biting
                                                                                                                                                                                       and Biting

                              (Vc=325sfm, D.O.C.=0.079", Wet)                                                        (Internal Evaluation) (Vc=175sfm, D.O.C.=0.049", Wet)           (Internal Evaluation)

   G40                                                                                                kyocera@kyocera-tools.ru                                                               U.S. Stock Standard : 
                                                                                                         www.kyocera-tools.ru                           World Express (Shipping: 7-10 Business Days) :